Understanding OSHA Stair Tread and Riser Requirements
Stair safety is paramount in any workplace, and the Occupational Safety and Health Administration (OSHA) has established clear guidelines to ensure this. This article delves into OSHA's stair tread and riser requirements, helping you maintain a safe and compliant workspace.
OSHA's General Stairway Requirements
Before diving into specific tread and riser requirements, it's essential to understand OSHA's general stairway requirements. According to OSHA 1910.23, stairways must have a minimum width of 22 inches, and the maximum rise for each step (riser) should not exceed 9.5 inches. The minimum tread depth should be at least 9 inches, measured horizontally from the leading edge of the tread to the vertical surface behind it.
OSHA Stair Tread Requirements
OSHA's stair tread requirements are designed to prevent trips and falls. The tread, the horizontal surface you step on, must be continuous and uniform. It should not have any openings or holes that could catch a foot or cause a person to trip. Additionally, the leading edge of the tread should not overhang the riser below it by more than 1/2 inch.

- Minimum Tread Depth: As mentioned earlier, the minimum tread depth should be at least 9 inches. This ensures that each step provides sufficient space for a person's foot, reducing the risk of trips and falls.
- Tread Surface: The tread surface should be slip-resistant to prevent falls due to slippery conditions. This is particularly important in workplaces with wet or oily surfaces.
- Tread Spacing: If open risers are used, the spacing between treads should not allow a 10-inch sphere to pass through. This is to prevent objects from falling through and causing injuries.
OSHA Stair Riser Requirements
OSHA's riser requirements are designed to ensure that each step has a consistent height, preventing trips and falls due to uneven steps. The maximum rise for each step should not exceed 9.5 inches, measured vertically between the leading edges of two adjacent treads.
- Maximum Riser Height: The maximum riser height of 9.5 inches ensures that each step is not too high, preventing people from having to stretch their legs too far to reach the next step.
- Riser Uniformity: All risers in a flight of stairs should be uniform in height. Inconsistent riser heights can lead to trips and falls.
Exceptions to OSHA's Stair Tread and Riser Requirements
While OSHA's stair tread and riser requirements apply to most workplaces, there are some exceptions. For instance, existing stairs that do not comply with these requirements may be allowed to remain if they are in good condition and do not pose a safety hazard. However, any new stairs or stairways that are constructed or modified must comply with these requirements.
Ensuring Compliance with OSHA Stair Requirements
To ensure your workplace is compliant with OSHA's stair tread and riser requirements, regular inspections and maintenance are crucial. Here are some steps you can take:

- Conduct regular visual inspections of your stairs to ensure they are in good condition and comply with OSHA's requirements.
- Perform periodic maintenance to repair any damaged treads or risers and to ensure that all stairs are slip-resistant.
- Provide adequate lighting for all stairways to ensure that they are visible and safe to use.
- Train your employees on the safe use of stairs and the importance of reporting any hazards or damage.
By understanding and adhering to OSHA's stair tread and riser requirements, you can help ensure a safe workplace for your employees. Regular inspections and maintenance, along with proper training, are key to maintaining compliance and preventing accidents.
More Details
Vertical clearance above any stair tread to any overhead obstruction is at least 6 feet, 8 inches (203 cm), as measured from the leading edge of the tread.

Guardrails Stair Requirements · OSHA · Riser Height – 1910.25(c)(2) Have a maximum riser height of 9.5 inches (24 cm); · Tread Depth – 1910.25(c)(3) Have a minimum ...

OSHA's intention for the 9.5-inch minimum tread depth requirement is to provide stepping space that is adequate to protect employees from falling, which is ...

29.03.2020 ... Rise must be a minimum of 6 ½ inches and a maximum of 9 ½ inches, but this corresponds to the angle of the stairs. For example, the standards ...

Handrail Strength: OSHA mandates that handrails must be able to withstand a force of at least 200 pounds (90.7 kg) applied in any direction. This ensures that ...

08.05.2026 ... OSHA's – 1910.25 Stairways– Important things to know · Required at every 12 feet of vertical rise · Must be free of obstructions and hazards.

06.01.2026 ... Handrails: Stairways with four or more risers need at least one handrail supporting 200 lbs. of force in any direction. Height must be 36-37 ...

25.03.2025 ... If the stairway has more than four risers, handrails are necessary even if both sides of the stairs are enclosed by walls. 2. Vertical Clearance ...

If the stairs have nosings, you measure from the leading edge of the nosing to the edge of the next step's nosing. Compliance, Stair Depth, Riser Height. OSHA ...

Introduction. 1. • OSHA Definitions – Stair, Stair Rail, and Guardrail Systems. 2. • Stair Systems. 3. • Stairway Handrail Requirements.

Requirements · Install stairways at 30 to 50 degrees from the horizontal. · Do not exceed variations in riser height or stair tread depth more than 1/4 inch in ...

Variations in riser height or tread depth shall not be over ¼-inch (0.6 cm) in any stairway system. 1926.1052(a)(4). Where doors or gates open directly on a ...

07.05.2024 ... According to OSHA regulations (29 CFR 1910.23), industrial stairs must be equipped with guardrails along open sides to prevent falls.

18.10.2022 ... Riser Heights and Tread Depths · OSHA makes provision for a maximum riser height of 9.5 inches with no minimum requirement [OSHA 1910.25 (c)(2)] ...

... stair requirements, IBC stair requirements, and OSHA stair regulations. Each set of codes outlines specific criteria for tread depth, riser height, nosing ...

14.07.2025 ... OSHA requires that stair risers be between 6 to 7.5 inches in height and tread depths be a minimum of 10 inches. Inconsistent step heights—even ...

Minimum tread width 22 IN (56 CM), Minimum Tread Depth 9.5 IN (24 CM), Maximum Riser Height 9.5 IN (24 CM). Related Code Sections. 1910.25( ...

Stair Rails vs. Handrails Requirements · Handrails must be at least 30 inches but not more than 38 inches as measured from the leading edge of the stair tread to ...

The requirements of OSHA safety regulations for the safe use of ladders and stairs (Subpart X, Title 29 Code of Federal Regulations, Part. 1926.1050 through ...

They must be 34–38 inches high, continuous, and include 12 inches of horizontal extension at the top and bottom landings. Can a stairway be both ADA and OSHA ...
