Keeping your Black & Decker weed wacker in peak condition starts with the simple, often overlooked task of loading the spool correctly. A tangled or poorly wound line is the primary cause of frustrating line breakage and inefficient cutting, turning a quick yard job into a chore. This guide walks you through the process step-by-step, ensuring you get the most power and longevity from your line.
Understanding Your Spool System
Before you begin, it is essential to recognize that not all spools are created equal. Black & Decker utilizes two primary designs: the single-line twist system and the more common dual-line bump system. The twist system requires you to manually wind the line in a specific direction to create tension, while the bump system uses two interlocking segments that release line on impact. Consult your user manual to identify which mechanism your model uses, as this dictates the winding procedure.
Preparing the Spool and Line
Gather your supplies, which include the new spool, your remaining line, and a pair of sharp scissors. Start by ensuring the spool is clean and free of old, brittle debris that could cause weak points in the new line. Locate the small arrows molded into the plastic of the spool; these indicate the precise direction the line must be wound. Ignoring these arrows is the most common mistake, as it causes the line to loosen and tangle during operation.
- Measure out the required length of line, typically between 10 and 20 feet depending on your model.
- Feed the line through the eyelets and any guide holes on the spool.
- Secure the end of the line to the spool using a small piece of tape or a built-in notch to prevent slippage.
The Winding Process
With the line prepared, hold the spool securely in one hand and begin feeding the line in the direction of the arrow. Maintain consistent tension as you wrap, but do not over-stretch the line, as this can cause it to become brittle. Loop the line neatly and uniformly across the spool, avoiding overlaps or crossing patterns. A tight, organized wind ensures smooth ejection and prevents the line from catching on the spool body during use.
| Step | Action | Critical Tip |
|---|---|---|
| 1 | Anchor the line end to the spool. | Use tape or a notch to prevent movement. |
| 2 | Begin winding in the arrow direction. | Keep tension firm but not aggressive. |
| 3 | Lay down the first loop firmly. | This loop sets the alignment for the rest. |
| 4 | Continue winding until 1/8" from the edge. | Do not fill to the absolute brim. |
Securing the Line and Reassembly
Once the spool is wound, leave a tail of approximately two inches and tuck the end into the designated slot or under a coil to lock it in place. Carefully remove the spool from your workspace and inspect it for any slack or irregular winding. Now, reattach the spool to the weed wacker head, following the reverse steps of your disassembly. Ensure that the release mechanism or cover is properly seated; a loose spool housing will disrupt the bump action and lead to line jamming.
Finally, test the mechanism before you head to the yard. With the unit unplugged or the battery removed, engage the line feed mechanism to verify that the line extends smoothly and retracts without hesitation. Proper winding creates the foundation for efficient cutting, allowing the centrifugal force to do the work while you guide the tool. Mastering this task saves time, reduces waste, and ensures a clean cut every time.
More Details
12.09.2017 ... This was the only video on my new weedwhacker that I needed to watch. Thank you so much, you are like a God to me, I wish my doctors could do as ...
01.03.2024 ... Press the spool down GENTLY and rotate it until you feel it drop into place. (When in place, the spool will turn a few degrees left and right ...
10.03.2025 ... How to replace weed eater string on Black & Decker 20V weed wacker. Stop wasting time and restring your Black + Decker weed wacker the ...
12.03.2018 ... Video tutorial on how to string a Black & Decker weed wacker LINK TO EXTRA STRING ( AMAZON) https://amzn.to/3aJKHtQ LINK TO THE SPRING LEVER ...
Wind the line around the spool, following the arrows on the spool. Feed the line through the hole and begin to wrap it around the spool. The more you overlap ...
10.05.2024 ... In this video, I'll walk you through replacing the string trimmer line on your Black & Decker trimmer. I'll show you how to take it apart, ...
24.03.2026 ... To wind a new line on a dual line spool, please follow the steps below Unplug the string trimmer, or remove its battery. Remove the...
03.04.2017 ... r/DIY - How to reuse Black & Decker AF-100 weed wacker spools ... How To Restring a 2 sided spool on a string trimmer weed eater · r ...
17.03.2025 ... Unplug the weed eater from the power source. · Remove the trimmer head by unscrewing the cap. · Remove the old string from the trimmer head. · Cut ...
20.07.2022 ... How to add string to Black & Decker weed Eater with AFS automatic Feed Spool Line .065 trimmer line the easy way. How to replace the AF 100 ...
15.10.2024 ... Next take your new line and string it through the holes. At this point. you wanna make sure the amount of line is even. on both sides. The only ...
02.01.2012 ... Take out the empty spool and locate the line holes. Cut a suitable length of nylon line (usually 10-15 feet), insert one end into the anchor ...
27.04.2024 ... Black and Decker Trimmer Line Spool Replacement - Change the Automatic Feed Spool (AFS) B&D Trimmer Product Links: Black & Decker Trimmer ...
26.07.2016 ... 3y. Profile photo of Brian. Brian Keith Smith. I need prestrung spool for electio weed eater. Brush hog Black and Decker. How do I order. Call ...
26.02.2014 ... Turn off and unplug the trimmer. · Press the tabs on the line hub cap and pull it off. · Pull the spool off the trimmer and remove any excess line ...
21.05.2025 ... In this video I show how to quickly and easily replace a broken spool cap for a 14 in. 6.5 AMP Corded Electric Single Line 2-in-1 String ...
Dual-line grass trimmers have two lines spinning from the spool, requiring a little extra effort to wind. ... Your weed trimmer/edger keeps overgrowth at ...
18.06.2020 ... Hot to Fix Won't Feed Line Black+Decker 20V Cordless String Weed Trimmer Edger LSTE525. Black & Decker has a beautiful design.
12.08.2018 ... 1.9K votes, 221 comments. My mind was always blown that people would even think of buying pre-loaded spools when it's so easy to keep on ...
15.06.2023 ... This here is a 60 volt string trimmer. from Greenworks Tools. To begin, simply twist the head and line up the green lines. Next take your new ...
