Torsion Bar Boot Install at Jean Partain blog

Torsion Bar Boot Install. So i found a plastic plumbing connector that is the exact diameter of the torsion bar (point to point). Question, i got new 1.06 torsion bars, and the dust boots inner diameter opening is about 1/2 the outter diameter of the torsion bar. I started with a 3/4 long socket, then pushed it over the socket onto a 7/8 socket, then onto a 1 socket to a 1 1/6 then last onto. Be sure to install the dust boot cover onto the torsion bar so that when the bar is inserted into the crossmember of the frame, the boot is toward the front of the car and seals out. 6) install torsion bar rubber boot on the engine side of the tranmission crossmember 7) add grease to the lower. Maybe if you put the boot on the bar. I gave up on those boots, cause i couldn't slide them on (with the bar in the car) using one hand to hold the bar and the other to work the boot. I believe my torsion bars are factory 318. I've got the energy suspension torsion bar dust boots and i'm trying to install them. It is the beige piece in the. Put a floor jack under the spindle to hold it in position, and raise/lower it as needed. You can also tap on the finger of the height adjuster to rotate the socket where the.

I gave up on those boots, cause i couldn't slide them on (with the bar in the car) using one hand to hold the bar and the other to work the boot. So i found a plastic plumbing connector that is the exact diameter of the torsion bar (point to point). I believe my torsion bars are factory 318. Be sure to install the dust boot cover onto the torsion bar so that when the bar is inserted into the crossmember of the frame, the boot is toward the front of the car and seals out. You can also tap on the finger of the height adjuster to rotate the socket where the. Put a floor jack under the spindle to hold it in position, and raise/lower it as needed. 6) install torsion bar rubber boot on the engine side of the tranmission crossmember 7) add grease to the lower. I started with a 3/4 long socket, then pushed it over the socket onto a 7/8 socket, then onto a 1 socket to a 1 1/6 then last onto. It is the beige piece in the. Question, i got new 1.06 torsion bars, and the dust boots inner diameter opening is about 1/2 the outter diameter of the torsion bar.

How To Adjust Mopar Torsion Bars RacingJunk News

Torsion Bar Boot Install Be sure to install the dust boot cover onto the torsion bar so that when the bar is inserted into the crossmember of the frame, the boot is toward the front of the car and seals out. I started with a 3/4 long socket, then pushed it over the socket onto a 7/8 socket, then onto a 1 socket to a 1 1/6 then last onto. I believe my torsion bars are factory 318. So i found a plastic plumbing connector that is the exact diameter of the torsion bar (point to point). Put a floor jack under the spindle to hold it in position, and raise/lower it as needed. You can also tap on the finger of the height adjuster to rotate the socket where the. I gave up on those boots, cause i couldn't slide them on (with the bar in the car) using one hand to hold the bar and the other to work the boot. 6) install torsion bar rubber boot on the engine side of the tranmission crossmember 7) add grease to the lower. Question, i got new 1.06 torsion bars, and the dust boots inner diameter opening is about 1/2 the outter diameter of the torsion bar. Be sure to install the dust boot cover onto the torsion bar so that when the bar is inserted into the crossmember of the frame, the boot is toward the front of the car and seals out. It is the beige piece in the. Maybe if you put the boot on the bar. I've got the energy suspension torsion bar dust boots and i'm trying to install them.