Replacing a Tub Spout with a Diverter: A Comprehensive Guide
Is your tub spout leaking, or perhaps you're looking to add a hand shower to your bathtub? Replacing your tub spout with a diverter is a straightforward DIY project that can significantly enhance your bathroom experience. In this guide, we'll walk you through the process step by step, ensuring you have all the information you need to complete the task safely and effectively.
Understanding Tub Spouts and Diverters
Before we dive into the replacement process, let's quickly understand what we're working with. A tub spout is the outlet where water flows into your bathtub. A diverter, on the other hand, is a valve that allows water to flow from the faucet to the tub spout or the showerhead, depending on which one you're using.
Tools and Materials Needed
Before you start, ensure you have the following tools and materials on hand:

- New tub spout with diverter
- Adjustable wrench
- Teflon tape
- Plumber's grease
- Rag or towel
- Bucket
Preparation: Turning Off the Water Supply
Before you begin any work on your plumbing, it's crucial to turn off the water supply to the tub. Locate the shutoff valve under the sink or behind the access panel and turn it clockwise until it stops. To confirm the water is off, try running the tub faucet; no water should come out.
Removing the Old Tub Spout
With the water supply turned off, you can now remove the old tub spout. Here's how:
- Use an adjustable wrench to loosen and remove the packing nut that secures the spout to the faucet.
- Gently pull the old spout away from the faucet. If it's stuck, you may need to use a bit of force, but be careful not to damage the faucet.
- Clean the threads on the faucet with a rag or towel to remove any old plumber's grease or debris.
Installing the New Tub Spout with Diverter
Now that the old spout is removed, it's time to install the new one with the diverter. Here's how:

- Wrap the threads of the new spout with Teflon tape to create a watertight seal. Wrap it clockwise, overlapping each layer by half.
- Apply a small amount of plumber's grease to the threads to help prevent seizing and make it easier to remove the spout in the future.
- Screw the new spout onto the faucet by hand, turning it clockwise until it's snug but not overly tight.
- Use an adjustable wrench to tighten the spout an additional quarter to half turn. Be careful not to overtighten and strip the threads.
- Reattach the packing nut and tighten it by hand.
- Turn the water supply back on and check for any leaks around the new spout. If there are no leaks, your new tub spout with diverter is successfully installed!
Testing the Diverter
Before you pack up your tools, it's essential to test the diverter to ensure it's working correctly. Here's how:
- Turn on the bathtub faucet and let the water run for a few seconds to fill the pipes.
- Pull the diverter lever to direct the water flow to the showerhead. The water should stop flowing from the tub spout and start flowing from the showerhead.
- Push the diverter lever back to its original position to redirect the water flow back to the tub spout.
If the diverter is working correctly, you should now have a fully functional tub spout with a diverter that allows you to switch between filling the tub and using the showerhead.
Troubleshooting Common Issues
While replacing a tub spout with a diverter is generally a straightforward task, you may encounter some issues along the way. Here are a few common problems and their solutions:

| Issue | Solution |
|---|---|
| Leaking around the new spout | Tighten the packing nut or wrap additional Teflon tape around the threads. |
| Diverter not working | Check that the diverter valve is fully engaged when you pull or push the lever. If it's still not working, the diverter may be faulty, and you'll need to replace it. |
| Water not flowing from the showerhead | Check that the showerhead is correctly attached and that there are no kinks in the hose. If the problem persists, you may have a clog in the showerhead or the pipes, and you'll need to clean or unclog them. |
If you're still having trouble after trying these solutions, it's best to consult a professional plumber to diagnose and fix the issue.
Replacing a tub spout with a diverter is a rewarding DIY project that can significantly improve your bathroom experience. By following this comprehensive guide, you'll have your new tub spout with diverter installed in no time, allowing you to enjoy both a relaxing bath and a convenient shower. Happy plumbing!






















