The 1UZ fits in the bay as if it were meant to be in a Cressida like it fits in the LS400. Plenty of room in the engine bay. I do have a complaint though. The stock Cressida steering rack shaft gets in the way of the driver side exhaust header. There is 3 options here. 1 is to move the factory rack over to the left about an inch and recenter the steering, 2 use a LS400 rack and lose turning.
Here's the full 1UZ Cressida build condensed into a 30-minute video! Huge thank you to Tune Technic, find their webshop below more.
Here are the specs /parts / maintenance: Drivetrain: - 1985 Toyota Cressida Wagon ~ 140k miles - 1995 Lexus 2nd gen 1UZFE 4.0L V8 swap (CA BAR approved) - 1995 Lexus automatic transmission - Fully functioning ODBII (but since it's a 95, the techs still do the ODB 1 procedures for smog).
Like this 1991 Toyota Cressida with 1UZ V8 and 5-speed manual offered for $8,000 in SF Bay Area, CA via craigslist. Tip from Kaibeezy. This isn't some kind of rare machine offered for pennies on the dollar, but the Cressida was the last Toyota badged car to leave the factory with rear-wheel-drive (before the FR-S was released a few years ago).
1988 Toyota Cressida 1uz Swap | Toyota Nation Forum
Here are the specs /parts / maintenance: Drivetrain: - 1985 Toyota Cressida Wagon ~ 140k miles - 1995 Lexus 2nd gen 1UZFE 4.0L V8 swap (CA BAR approved) - 1995 Lexus automatic transmission - Fully functioning ODBII (but since it's a 95, the techs still do the ODB 1 procedures for smog).
Similar threads 1uz into mx73 cressida *pics update* Peewee Jun 17, 2004 Swap, Conversion, Transplant, Specialty Vehicles 2 3 Replies 55 Views 12K Jun 29, 2005.
The 1UZ fits in the bay as if it were meant to be in a Cressida like it fits in the LS400. Plenty of room in the engine bay. I do have a complaint though. The stock Cressida steering rack shaft gets in the way of the driver side exhaust header. There is 3 options here. 1 is to move the factory rack over to the left about an inch and recenter the steering, 2 use a LS400 rack and lose turning.
Bid for the chance to own a 1UZ-Powered 1985 Toyota Cressida Station Wagon at auction with Bring a Trailer, the home of the best vintage and classic cars online. Lot #208,158.
Toyota Cressida (MX32) With 1UZ-FE Swap : Vintagejapaneseautos
Here are the specs /parts / maintenance: Drivetrain: - 1985 Toyota Cressida Wagon ~ 140k miles - 1995 Lexus 2nd gen 1UZFE 4.0L V8 swap (CA BAR approved) - 1995 Lexus automatic transmission - Fully functioning ODBII (but since it's a 95, the techs still do the ODB 1 procedures for smog).
Now I'm falling even deeper in love because someone plopped one beneath the hood of a humble Toyota Cressida wagon, and it's for sale. The 1UZ.
1UZ into MX73 Cressida kitUses factory engine rubber mounts Good swaybar clearance Both A340 and W58 can be used with the standard automatic gearbox crossmember. Note: the standard 1uz A341 gearbox has a different gearbox rubber mount bolt pattern so if going that route you would need to elongate the holes on the gearbox crossmember. You will need to either cut and plate the corner of the cam.
Bid for the chance to own a 1UZ-Powered 1985 Toyota Cressida Station Wagon at auction with Bring a Trailer, the home of the best vintage and classic cars online. Lot #208,158.
Now I'm falling even deeper in love because someone plopped one beneath the hood of a humble Toyota Cressida wagon, and it's for sale. The 1UZ.
Similar threads 1uz into mx73 cressida *pics update* Peewee Jun 17, 2004 Swap, Conversion, Transplant, Specialty Vehicles 2 3 Replies 55 Views 12K Jun 29, 2005.
Here are the specs /parts / maintenance: Drivetrain: - 1985 Toyota Cressida Wagon ~ 140k miles - 1995 Lexus 2nd gen 1UZFE 4.0L V8 swap (CA BAR approved) - 1995 Lexus automatic transmission - Fully functioning ODBII (but since it's a 95, the techs still do the ODB 1 procedures for smog).
1988 toyota cressida 1uz swap Jump to Latest 21K views 17 replies 13 participants last post by Toyodafan00 Feb 9, 2023 cressida19881uz Discussion starter.
Toyota Cressida 1UZ - YouTube
1UZ into MX73 Cressida kitUses factory engine rubber mounts Good swaybar clearance Both A340 and W58 can be used with the standard automatic gearbox crossmember. Note: the standard 1uz A341 gearbox has a different gearbox rubber mount bolt pattern so if going that route you would need to elongate the holes on the gearbox crossmember. You will need to either cut and plate the corner of the cam.
The 1UZ fits in the bay as if it were meant to be in a Cressida like it fits in the LS400. Plenty of room in the engine bay. I do have a complaint though. The stock Cressida steering rack shaft gets in the way of the driver side exhaust header. There is 3 options here. 1 is to move the factory rack over to the left about an inch and recenter the steering, 2 use a LS400 rack and lose turning.
Here's the full 1UZ Cressida build condensed into a 30-minute video! Huge thank you to Tune Technic, find their webshop below more.
Now I'm falling even deeper in love because someone plopped one beneath the hood of a humble Toyota Cressida wagon, and it's for sale. The 1UZ.
This 1UZ-swapped Toyota Cressida Wagon Must Rip - Hooniverse
Here's the full 1UZ Cressida build condensed into a 30-minute video! Huge thank you to Tune Technic, find their webshop below more.
Similar threads 1uz into mx73 cressida *pics update* Peewee Jun 17, 2004 Swap, Conversion, Transplant, Specialty Vehicles 2 3 Replies 55 Views 12K Jun 29, 2005.
1988 toyota cressida 1uz swap Jump to Latest 21K views 17 replies 13 participants last post by Toyodafan00 Feb 9, 2023 cressida19881uz Discussion starter.
Like this 1991 Toyota Cressida with 1UZ V8 and 5-speed manual offered for $8,000 in SF Bay Area, CA via craigslist. Tip from Kaibeezy. This isn't some kind of rare machine offered for pennies on the dollar, but the Cressida was the last Toyota badged car to leave the factory with rear-wheel-drive (before the FR-S was released a few years ago).
1988 Toyota Cressida 1uz Swap - Toyota Nation Forum : Toyota Car And ...
Here's the full 1UZ Cressida build condensed into a 30-minute video! Huge thank you to Tune Technic, find their webshop below more.
Now I'm falling even deeper in love because someone plopped one beneath the hood of a humble Toyota Cressida wagon, and it's for sale. The 1UZ.
Bid for the chance to own a 1UZ-Powered 1985 Toyota Cressida Station Wagon at auction with Bring a Trailer, the home of the best vintage and classic cars online. Lot #208,158.
Justin Lucas stopped by The Donut Mill to show off his 1979 Toyota Cressida. Justin replaced the factory powertrain with a 4.0 L 1UZ V8, R154 five-speed manual transmission, and narrowed Ford 7.5.
The Project Car Begins: 1UZ + Toyota Cressida : R/projectcar
1UZ into MX73 Cressida kitUses factory engine rubber mounts Good swaybar clearance Both A340 and W58 can be used with the standard automatic gearbox crossmember. Note: the standard 1uz A341 gearbox has a different gearbox rubber mount bolt pattern so if going that route you would need to elongate the holes on the gearbox crossmember. You will need to either cut and plate the corner of the cam.
Bid for the chance to own a 1UZ-Powered 1985 Toyota Cressida Station Wagon at auction with Bring a Trailer, the home of the best vintage and classic cars online. Lot #208,158.
Here are the specs /parts / maintenance: Drivetrain: - 1985 Toyota Cressida Wagon ~ 140k miles - 1995 Lexus 2nd gen 1UZFE 4.0L V8 swap (CA BAR approved) - 1995 Lexus automatic transmission - Fully functioning ODBII (but since it's a 95, the techs still do the ODB 1 procedures for smog).
1988 toyota cressida 1uz swap Jump to Latest 21K views 17 replies 13 participants last post by Toyodafan00 Feb 9, 2023 cressida19881uz Discussion starter.
Like this 1991 Toyota Cressida with 1UZ V8 and 5-speed manual offered for $8,000 in SF Bay Area, CA via craigslist. Tip from Kaibeezy. This isn't some kind of rare machine offered for pennies on the dollar, but the Cressida was the last Toyota badged car to leave the factory with rear-wheel-drive (before the FR-S was released a few years ago).
Similar threads 1uz into mx73 cressida *pics update* Peewee Jun 17, 2004 Swap, Conversion, Transplant, Specialty Vehicles 2 3 Replies 55 Views 12K Jun 29, 2005.
Here's the full 1UZ Cressida build condensed into a 30-minute video! Huge thank you to Tune Technic, find their webshop below more.
1UZ into MX73 Cressida kitUses factory engine rubber mounts Good swaybar clearance Both A340 and W58 can be used with the standard automatic gearbox crossmember. Note: the standard 1uz A341 gearbox has a different gearbox rubber mount bolt pattern so if going that route you would need to elongate the holes on the gearbox crossmember. You will need to either cut and plate the corner of the cam.
Toyota Cressida 1UZ V8 241.9 HP | By Queensland Chassis Dyno
Justin Lucas stopped by The Donut Mill to show off his 1979 Toyota Cressida. Justin replaced the factory powertrain with a 4.0 L 1UZ V8, R154 five-speed manual transmission, and narrowed Ford 7.5.
Similar threads 1uz into mx73 cressida *pics update* Peewee Jun 17, 2004 Swap, Conversion, Transplant, Specialty Vehicles 2 3 Replies 55 Views 12K Jun 29, 2005.
Here are the specs /parts / maintenance: Drivetrain: - 1985 Toyota Cressida Wagon ~ 140k miles - 1995 Lexus 2nd gen 1UZFE 4.0L V8 swap (CA BAR approved) - 1995 Lexus automatic transmission - Fully functioning ODBII (but since it's a 95, the techs still do the ODB 1 procedures for smog).
1UZ into MX73 Cressida kitUses factory engine rubber mounts Good swaybar clearance Both A340 and W58 can be used with the standard automatic gearbox crossmember. Note: the standard 1uz A341 gearbox has a different gearbox rubber mount bolt pattern so if going that route you would need to elongate the holes on the gearbox crossmember. You will need to either cut and plate the corner of the cam.
Justin Lucas stopped by The Donut Mill to show off his 1979 Toyota Cressida. Justin replaced the factory powertrain with a 4.0 L 1UZ V8, R154 five-speed manual transmission, and narrowed Ford 7.5.
Here's the full 1UZ Cressida build condensed into a 30-minute video! Huge thank you to Tune Technic, find their webshop below more.
The 1UZ fits in the bay as if it were meant to be in a Cressida like it fits in the LS400. Plenty of room in the engine bay. I do have a complaint though. The stock Cressida steering rack shaft gets in the way of the driver side exhaust header. There is 3 options here. 1 is to move the factory rack over to the left about an inch and recenter the steering, 2 use a LS400 rack and lose turning.
1UZ into MX73 Cressida kitUses factory engine rubber mounts Good swaybar clearance Both A340 and W58 can be used with the standard automatic gearbox crossmember. Note: the standard 1uz A341 gearbox has a different gearbox rubber mount bolt pattern so if going that route you would need to elongate the holes on the gearbox crossmember. You will need to either cut and plate the corner of the cam.
1988 Toyota Cressida 1uz Swap | Toyota Nation Forum
Similar threads 1uz into mx73 cressida *pics update* Peewee Jun 17, 2004 Swap, Conversion, Transplant, Specialty Vehicles 2 3 Replies 55 Views 12K Jun 29, 2005.
1988 toyota cressida 1uz swap Jump to Latest 21K views 17 replies 13 participants last post by Toyodafan00 Feb 9, 2023 cressida19881uz Discussion starter.
Justin Lucas stopped by The Donut Mill to show off his 1979 Toyota Cressida. Justin replaced the factory powertrain with a 4.0 L 1UZ V8, R154 five-speed manual transmission, and narrowed Ford 7.5.
1UZ into MX73 Cressida kitUses factory engine rubber mounts Good swaybar clearance Both A340 and W58 can be used with the standard automatic gearbox crossmember. Note: the standard 1uz A341 gearbox has a different gearbox rubber mount bolt pattern so if going that route you would need to elongate the holes on the gearbox crossmember. You will need to either cut and plate the corner of the cam.
1UZ Cressida @ Adams Motorsports Park : Drifting
Here are the specs /parts / maintenance: Drivetrain: - 1985 Toyota Cressida Wagon ~ 140k miles - 1995 Lexus 2nd gen 1UZFE 4.0L V8 swap (CA BAR approved) - 1995 Lexus automatic transmission - Fully functioning ODBII (but since it's a 95, the techs still do the ODB 1 procedures for smog).
1988 toyota cressida 1uz swap Jump to Latest 21K views 17 replies 13 participants last post by Toyodafan00 Feb 9, 2023 cressida19881uz Discussion starter.
Justin Lucas stopped by The Donut Mill to show off his 1979 Toyota Cressida. Justin replaced the factory powertrain with a 4.0 L 1UZ V8, R154 five-speed manual transmission, and narrowed Ford 7.5.
The 1UZ fits in the bay as if it were meant to be in a Cressida like it fits in the LS400. Plenty of room in the engine bay. I do have a complaint though. The stock Cressida steering rack shaft gets in the way of the driver side exhaust header. There is 3 options here. 1 is to move the factory rack over to the left about an inch and recenter the steering, 2 use a LS400 rack and lose turning.
1UZ into MX73 Cressida kitUses factory engine rubber mounts Good swaybar clearance Both A340 and W58 can be used with the standard automatic gearbox crossmember. Note: the standard 1uz A341 gearbox has a different gearbox rubber mount bolt pattern so if going that route you would need to elongate the holes on the gearbox crossmember. You will need to either cut and plate the corner of the cam.
Here are the specs /parts / maintenance: Drivetrain: - 1985 Toyota Cressida Wagon ~ 140k miles - 1995 Lexus 2nd gen 1UZFE 4.0L V8 swap (CA BAR approved) - 1995 Lexus automatic transmission - Fully functioning ODBII (but since it's a 95, the techs still do the ODB 1 procedures for smog).
The 1UZ fits in the bay as if it were meant to be in a Cressida like it fits in the LS400. Plenty of room in the engine bay. I do have a complaint though. The stock Cressida steering rack shaft gets in the way of the driver side exhaust header. There is 3 options here. 1 is to move the factory rack over to the left about an inch and recenter the steering, 2 use a LS400 rack and lose turning.
Similar threads 1uz into mx73 cressida *pics update* Peewee Jun 17, 2004 Swap, Conversion, Transplant, Specialty Vehicles 2 3 Replies 55 Views 12K Jun 29, 2005.
Like this 1991 Toyota Cressida with 1UZ V8 and 5-speed manual offered for $8,000 in SF Bay Area, CA via craigslist. Tip from Kaibeezy. This isn't some kind of rare machine offered for pennies on the dollar, but the Cressida was the last Toyota badged car to leave the factory with rear-wheel-drive (before the FR-S was released a few years ago).
Bid for the chance to own a 1UZ-Powered 1985 Toyota Cressida Station Wagon at auction with Bring a Trailer, the home of the best vintage and classic cars online. Lot #208,158.
1988 toyota cressida 1uz swap Jump to Latest 21K views 17 replies 13 participants last post by Toyodafan00 Feb 9, 2023 cressida19881uz Discussion starter.
Here's the full 1UZ Cressida build condensed into a 30-minute video! Huge thank you to Tune Technic, find their webshop below more.
Now I'm falling even deeper in love because someone plopped one beneath the hood of a humble Toyota Cressida wagon, and it's for sale. The 1UZ.
Justin Lucas stopped by The Donut Mill to show off his 1979 Toyota Cressida. Justin replaced the factory powertrain with a 4.0 L 1UZ V8, R154 five-speed manual transmission, and narrowed Ford 7.5.
