Installing a new tub faucet is one of the most rewarding DIY plumbing projects a homeowner can undertake. Whether you are updating an outdated look or fixing a leaky fixture, this upgrade transforms the functionality and aesthetic of your bathroom with minimal expense. By following a precise process, you can achieve a professional-looking result that eliminates the need for a costly service call.
Choosing the Right Tub Faucet
Before you begin the installation, selecting the correct hardware is essential for a smooth process. You must verify the configuration of your existing pipes, including the spacing between the hot and cold water inlets, usually measured in inches. Choosing a faucet with the same valve orientation and center measurement ensures a proper fit without requiring extensive modifications to the wall.
Tools and Material Preparation
Gathering the right tools beforehand prevents frustration and saves time. You will need an adjustable wrench, basin wrench, screwdrivers, plumber’s tape, and a bucket to catch residual water. Turning off the home’s main water supply is the critical first safety step, followed by opening the tub valve to drain any remaining pressure and water from the lines.
Removing the Old Fixture
Carefully removing the old faucet reveals the condition of your plumbing and sets the stage for the new installation. You will typically use a wrench to disconnect the supply lines from the valves and remove the mounting nuts that secure the fixture to the tub deck. It is vital to inspect the copper or PEX lines for any corrosion or damage, replacing them if necessary to prevent future leaks.
Installing the New Cartridge and Valve
For models with a separate hot and cold handle, the trim plate and old valve stem must be extracted to allow the new components to fit. Applying fresh plumber’s tape to the threads of the supply lines ensures a watertight seal when you reconnect them. Hand-tightening the nuts initially, followed by a quarter-turn with a wrench, provides the correct tension without risking damage to the brass fittings.
Testing for Leaks and Functionality
Once the fixture is secured, restoring the water supply allows you to verify the integrity of your work. You should turn on the water slowly, checking the valves and connections for any drips before the water reaches full pressure. Running the tub faucet through its full range of motion confirms that the handles operate smoothly and that the temperature mix is calibrated correctly.
Finalizing the Installation
After confirming there are no leaks, the final step involves securing the escutcheon plate and handles to complete the aesthetic. Tightening these components ensures a sleek finish that aligns with your bathroom’s design. A final check of the surrounding area for moisture guarantees a clean installation that is ready for daily use.
More Details
05.02.2021 ... Share your videos with friends, family, and the world.
17.08.2021 ... Give your bathroom an easy update by installing a bathtub spout with @thisoldhouse. Whether you're adding a new tub spout, or just replacing ...
30.06.2025 ... Step 1: Turn Off the Water Shut off your home's main water supply. · Step 2: Remove the Old Spout · Step 3: Remove Faucet Handles (If Replacing)
1. REMOVE THE FAUCET ASSEMBLY. Shut off water to the existing tub faucet. Cap the faucet outlet to avoid drips and tape over the drain trap. Using a tube cutter ...
05.12.2024 ... clean around the old drain, pop the new one in, and do everything in reverse. tighten the nuts, reconnect the supply lines. you're already ...
25.01.2023 ... How to Install a Bathroom Faucet This video is sponsored by easyfix ® – a virtual tool that connects you with a pro to get the support you ...
08.10.2025 ... A bathtub faucet might seem tricky, but a basic bathtub faucet replacement is a beginner-friendly replacement project. It usually takes 1–2 ...
1. Turn off the water supply and prepare the installation. 1.2 - Determine the location of the shower head, bathtub and shower, and bathtub spout if required.
Apply plumber tape to threads on pipe nipple and screw on tub spout. l':m IRON PIPE INSTALLATION. L:ia 1. Install pipe nipple so that end of nipple projects out ...
13.04.2025 ... Comment “BATH” & we'll send you the top brands we recommend for bathroom faucets! BATHROOM faucet buying tips, you need to know…. more. View ...
29.09.2021 ... Assemble the elbow and feed nipple. Screw into the bottom of the valve. Screw the tub spout nipple into the elbow. The nipple should extend out ...
15.01.2023 ... In this video, I show how to install a freestanding tub and faucet. The faucet I how to install is the Senlesen Free Standing Tub Faucet.
Want to install a new shower faucet? This video will walk you through the ... How to Install a Bathroom Fan. 2:55. How to Install a Bathroom Fan · How to ...
27.01.2024 ... Start by marking out between 1/4 inch. and an inch off that back wall. That's where the back of the adapters gonna sit. Then use some KY jelly ...
Score the caulking around your existing faucet with a box cutter. Loosen the tub spout's set screw with an Allen wrench, turning it counterclockwise.
25.05.2024 ... ... faucet seats: https://amzn.to/4fjjEnQ → Professional-grade Teflon tape — the right way to seal threaded connections: https://amzn.to ...
12.01.2022 ... Materials Needed: · Freestanding tub faucet kit · Adjustable wrench · Plumber's tape (Teflon tape) · Silicone sealant · Drill · Concrete drill ...
... Faucet Repair Parts · Garbage Disposer Repair Parts · Shut-Off Valves ... How to Install a Threaded Tub Spout. Step 1: Make sure that your new spout is ...
12.03.2026 ... How to Install Bathtub Faucet | Trusted Plumbing & Heating If you are ready to update your bathroom but not sure how to install bathtub ...
03.04.2026 ... Step four: replace the flush valve and tank-to-bowl gasket. Step five: install the new fill valve, flapper, and handle. Step six: reinstall the ...
