Creating a resin picture is a rewarding process that transforms a simple photograph into a vibrant, glossy keepsake. This technique involves pouring a clear epoxy resin over a printed image secured to a flat surface, allowing the resin to cure into a smooth, protective layer. The result is a high-gloss finish that deepens colors and gives the image a professional, almost jewel-like appearance.
Gathering Your Materials and Workspace
The success of your project begins long before the resin touches the photo. Preparation is key to achieving a flawless finish and avoiding stressful mid-process decisions. You will need a high-quality print on glossy photo paper, a rigid backing such as a floating frame or a sturdy board, and a clean epoxy resin kit specifically designed for art.
Essential Tools and Supplies
To ensure a smooth application, you must gather specific tools that help with measuring, mixing, and surface preparation. Precision is vital when mixing the two-part resin, so a digital scale is non-negotiable. You will also need mixing cups, silicone spreaders, and heat guns to eliminate bubbles.

- Epoxy resin and hardener (calculate volume based on your frame depth)
- Photographic print on gloss paper
- Rigid backing board or pre-made floating frame
- Digital kitchen scale and mixing cups
- Silicone spreader and heat gun
- Masking tape and nitrile gloves
Preparing the Image and Backing
Not all photographs are created equal when it comes to resin art. You should use a photo printed on glossy, thick cardstock rather than standard matte paper. The gloss coating prevents the resin from soaking into the paper fibers, ensuring the image stays vibrant and retains its color saturation once sealed.
Leveling the Surface
Before pouring, you must secure the print to the backing board. If you are using a frame with an open back, you will build a "lip" using hot glue or tape around the perimeter. This creates a dam that holds the liquid resin in place. The most critical step is ensuring the entire surface is perfectly level; even a slight tilt will cause the resin to pool on one side, distorting the final look.
The Mixing Process
This is the stage where patience is essential. Resin chemistry is sensitive; the wrong ratio or temperature can lead to sticky spots or improper curing. You must measure the resin and hardener by weight, not volume, using your digital scale to ensure accuracy. Stir the mixture slowly and thoroughly, scraping the sides and bottom of the cup to ensure no unmixed catalyst remains.

Temperature Matters
Warm resin flows better and cures faster. If the environment is cold, place the mixed resin cup in a warm water bath (ensure no water gets into the mixture). Stirring creates heat and air bubbles, so take your time. The goal is a clear, consistent liquid with a slow ribbon-like drip when you lift your stir stick.
Pouring and Protecting the Art
Once mixed, gently pour the resin over the center of the image. Let the resin flow outward naturally; you can guide it with your spreader, but avoid aggressive scraping. The goal is to coat the image evenly without disturbing the visual composition too much. If your design includes elements that float above the surface, pour carefully around them to create depth.
Bubble Elimination
After pouring, the surface will likely be covered in small bubbles. This is normal. Use your heat gun to sweep across the surface in a sweeping motion, heating the resin just enough to make the bubbles pop. You can also gently blow on the surface through a straw for spot treatment. Avoid using a torch if you are new to resin, as the intense heat can scorch the resin or ruin the image.

Curing and Final Touches
The waiting period is the final hurdle in this project. While the surface may feel dry within a few hours, the chemical reaction deep within the resin takes much longer. To achieve a glass-hard finish, you should allow the piece to cure in a dust-free environment for the time specified by the manufacturer, often up to 72 hours.
Dust Prevention
As the resin cures, it becomes tacky and attracts dust. To prevent your masterpiece from turning into a gritty mess, cover it loosely with a box or a clean plastic container. Dust particles that land on the curing surface will be forever trapped, so a little protection goes a long way. Once fully cured, remove the protective covering and enjoy your finished resin picture.





















