Installing recessed lights above your shower can significantly enhance your bathroom's ambiance and functionality. Not only do they provide much-needed task lighting, but they also create a sleek, modern look. However, it's crucial to ensure safety and compliance with electrical codes when working with lights in a wet area like the shower. This guide will walk you through the process of installing recessed lights above your shower, ensuring both safety and aesthetic appeal.

Before you begin, ensure you have the right tools and materials. You'll need a recessed light kit designed for wet locations, a junction box, electrical cable, wire connectors, a voltage tester, and basic tools like a drill, screwdriver, and pliers. Always consult your local electrical codes and obtain any necessary permits before starting the project.

Preparation and Planning
Proper planning is key to a successful installation. Measure the space above your shower to determine the number and placement of lights. Standard shower sizes are typically 36" x 36" or 36" x 48", but it's always best to measure your specific space. Recessed lights should be placed at least 6" away from the shower walls and 12" apart from each other for even lighting.

Choose a light fixture rated for wet locations. These fixtures have a higher Ingress Protection (IP) rating, making them resistant to water and moisture. The most common rating for shower lights is IP65, which offers protection against low-pressure water jets from any direction.
Selecting the Right Recessed Light

When choosing a recessed light for your shower, consider the following factors:
- Light Output: Determine the amount of light needed based on the size of your shower and your personal preference. A common choice is a 6-inch or 4-inch can light with a 700-1000 lumen bulb.
- Bulb Type: LED bulbs are energy-efficient and long-lasting, making them an excellent choice for recessed lights. They also produce less heat than incandescent bulbs, reducing the risk of moisture damage.
- Dimming Capability: If you want to control the light level, choose a fixture with dimming capability. Ensure the bulb is compatible with dimmers as well.
Understanding Recessed Light Types

Recessed lights come in two main types: new construction and remodeling. New construction lights are installed during the initial build of the home, while remodeling lights are designed for retrofit installations in existing ceilings. For shower installations, you'll typically use remodeling lights, which come with a housing that fits into the ceiling and a trim piece that covers the opening.
Some remodeling lights are designed for installation in insulated ceilings, while others are not. Ensure you choose a light rated for your specific ceiling type to avoid heat buildup and potential fire hazards.
Installing Recessed Lights Above the Shower

Once you've chosen the right light and planned your installation, it's time to begin the physical work. Always turn off the power to the circuit you'll be working on at the main electrical panel and use a voltage tester to ensure the wires are dead before starting.
Before cutting into the ceiling, mark the locations of your lights using a pencil and a level. The center of the light should be about 12" from the shower walls and 12" apart from each other. Use a drill with a hole saw bit to cut out the holes for the light housings. Ensure the holes are slightly smaller than the housing to create a snug fit.




















Installing the Recessed Light Housing
Insert the light housing into the hole you've created, ensuring it's level and flush with the ceiling. Secure the housing in place using the provided screws or clips. Some housings may require additional support, such as a brace or a spring clip, to hold them securely in place.
Once the housing is secure, connect the electrical wires according to the manufacturer's instructions. Typically, you'll connect the black (hot) wire to the black wire in the housing, the white (neutral) wire to the white wire, and the green or bare (ground) wire to the green or bare wire. Use wire connectors to join the wires, ensuring they're securely connected and free of any gaps or twists.
Installing the Recessed Light Trim
After the electrical connections are complete, install the trim piece that covers the opening of the housing. This piece is usually secured with clips or screws and provides a finished look to the light fixture. Ensure the trim is level and centered over the housing.
Before turning the power back on, double-check all electrical connections to ensure they're secure and free of any gaps or twists. Use a voltage tester to ensure the wires are still dead before turning the power back on at the main electrical panel.
Now that your recessed lights are installed, enjoy the enhanced ambiance and functionality they bring to your bathroom. Regularly clean the lights to remove any soap scum or moisture buildup, and always consult a licensed electrician if you encounter any issues or are unsure about any aspect of the installation process.