Color grading SLog3 footage in Premiere Pro is one of the most critical steps in transforming raw, flat video into cinematic, high-dynamic-range content. Sony’s S-Log3 gamma curve is designed to capture an extensive dynamic range and rich color information, but it appears dull and contrasty until properly graded. This guide walks you through the entire process, from preparation to final export, ensuring you can maximize the potential of your SLog3 media.

Understanding SLog3 and the Preparation Stage

Before diving into the technical adjustments, it is essential to understand why SLog3 requires special handling. Unlike standard gamma, SLog3 flattens the image and shifts the color balance significantly toward the blue-magenta spectrum. This is intentional, as it reserves maximum data in the shadows where sensor noise is typically highest. If you skip the foundational setup, you will struggle to achieve clean results later in the timeline.
Project Settings and Camera Configuration

To begin, you must ensure your project settings match the footage to avoid automatic misinterpretation by the software. Premiere Pro relies on the metadata attached to the clip, but it is good practice to configure your sequence manually for precision.
Setting Up Your Sequence

- Create a new sequence that matches the resolution and frame rate of your source footage.
- Navigate to the "Color Settings" of the sequence and set the "Color Space" to "SLog3 Gamma" and "Color Encoding" to "S-Gamut3.cine".
- If you are working alongside HDR displays, you may opt for HLG or PQ, but for standard grading, SLog3/SGamut is the correct choice.
Applying the Input LUT (Look-Up Table)
The most crucial step in grading SLog3 is converting the flat image into a viewable picture using a gamma conversion. A LUT handles this by applying a formula that adjusts the brightness and color balance in real-time. Without this, your scopes will show clipped blacks and overly saturated colors, making accurate grading impossible.

You can apply a basic Creative LUT or, better yet, use the "Sony SLog3 to Rec.709" LUT provided by Adobe or Sony. Keep in mind that this LUT is merely a starting point; it gives you a contrasty image to work on, but you will need to adjust the exposure and color temperature to suit your specific shot.
Core Grading Workflow: Exposure and Contrast
Once the LUT is applied and the image is visible, you should assess the scene using the waveform monitor and vectorscope. With SLog3, the goal is to lift the shadows and protect the highlights.

Using the Lumetri Color panel, begin by adjusting the "Exposure" slider. In SLog3, middle gray is typically exposed around 30-40 IRE, so you will often need to increase exposure significantly compared to standard video. Next, manipulate the "Highlights" slider to recover blown-out areas, and use the "Shadows" slider to lift the black levels. Avoid crushing the blacks too much, as SLog3 relies on the lifted shadow detail to maintain dynamic range.
Color Correction and Matching




















After mastering the luminance, you must address the color cast. SLog3 footage tends to have a magenta bias, which can look unnatural if left unchecked.
- Use the "Offset" tab to perform a primary color balance, correcting any extreme shifts in the shadows.
- Move to the "Gain" tab to adjust the mid-tones, which usually contain the skin tones and primary subject matter.
- Finally, tweak the "Lift" tab to fine-tune the black levels and introduce a subtle contrast curve.
It is generally recommended to resolve the luminance issues before diving deep into saturation. Once the image looks neutral, you can use the "HSL Secondary" qualifier to isolate specific colors (like sky or foliage) and adjust their hue and saturation independently.
Final Output and Best Practices
After achieving a balanced grade, ensure your export settings maintain the quality of your work. SLog3 material is high-bitrate, so using a high-quality H.264 preset or an Apple ProRes codec is highly recommended to avoid compression artifacts.
Remember to monitor your scopes constantly. A properly graded SLog3 image should show a healthy histogram spread across the entire graph, with the waveform peaking near 70-90 IRE for bright scenes. By following these steps, you transform generic footage into a visually striking piece that retains the latitude and depth Sony intended when capturing the scene.