Installing shiplap on an uneven wall is a project that transforms a space with character, but it demands a methodical approach rather than a straightforward application. While perfectly straight walls provide an ideal, predictable surface, most real-world scenarios—especially in older homes, studios, or cottages—feature subtle imperfections that require specific techniques. The goal is not to fight the wall’s natural topography but to work with it, creating a visually flat and professional finish that masks the underlying irregularities. This guide walks you through the strategic process, from assessment to finishing touches, ensuring your shiplap installation looks intentional and flawless.
Assessing the Wall's True Condition
Before removing a single board, conduct a thorough evaluation of the wall's condition. Use a long, straight level or a ruler pressed against the wall to identify the nature and extent of the unevenness. Determine if the irregularities are caused by plaster lath, old drywall seams, water damage, or structural bowing. Next, measure the depth of the deviation using shims or a thin gauge; if the gap is thinner than a standard playing card (about 0.01 inches), you might manage with a flexible adhesive. However, if the gaps are deeper or the surface is wavy, you will almost certainly need to install a substrate to create a flat plane.
Choosing the Right Substrate
The substrate is the critical foundation that corrects the wall’s imperfections and provides a stable surface for the shiplap. For most uneven walls, 1/2-inch or 5/8-inch drywall is the go-to material, as it is rigid enough to bridge gaps and provides a solid nailing surface. Alternatively, if the wall is significantly uneven or you require extra insulation, you might opt for 1x4 or 1x6 furring strips. These wooden strips are nailed horizontally to the wall, allowing you to level the surface by adjusting the thickness of the spacers. This method is particularly effective for historic homes where wall depth varies dramatically.

Preparation and Material Calculation
Once the substrate strategy is decided, preparation becomes the key to efficiency. Remove any baseboards, outlet covers, and hanging hardware, and label them for reinstallation. Turn off the power at the breaker if working around electrical fixtures, and use a stud finder to locate the vertical supports behind the wall. Mark the stud locations on the substrate or furring strips, as this dictates where your nails or screws must go. Calculate the linear footage of your shiplap by measuring the wall height and multiplying it by the number of columns, adding an extra 10% for waste and cuts. This ensures you purchase the correct amount of material without running short mid-project.
Addressing Electrical and Obstructions
Handling fixtures and obstructions requires precision to maintain the integrity of the shiplap design. When you encounter an outlet or switch, turn off the power and carefully remove the fixture. If the box is flush with the new substrate depth, you may simply cut a hole in the shiplap to fit around it. For boxes that protrude, you have two primary options: use a deeper electrical box extender to bring the fixture flush with the wall, or mill a small section of the shiplap board to recess behind the fixture. The latter option maintains a flat surface but requires careful cutting to ensure the joint remains clean and the seal is tight.
With the wall prepared and the substrate installed, it is time to plan the layout. Starting at the center of the wall is generally the best practice, as it balances the boards and minimizes the appearance of awkward cuts at the edges. Use a level to draw a vertical plumb line down the center of the substrate. Dry-fit the first row of shiplap, snapping a line to mark where the top of the board meets the ceiling. This visual guide ensures that the boards remain straight and that the "shadow gap" between each piece remains consistent. Remember to stagger the vertical seams of the boards in a brick-like pattern; this aesthetic detail prevents the eye from perceiving a series of vertical cracks and adds structural stability to the wall.

Installation and Finishing Touches
Apply a continuous bead of construction adhesive to the back of the shiplap, focusing on the edges and center for maximum hold. For large walls, utilize a nail gun with 2-inch finishing nails to secure the board through the substrate, driving the nails into the wall studs or furring strips at every second or third board. Pay attention to the gap between the floor and the bottom board; you have two aesthetic choices. You can leave a small gap to accommodate wood movement, which is the traditional approach, or you can tuck the shiplap tightly into the floor if the transition is covered by baseboard trim. Ensure that the tongue and groove connection remains tight as you work upward, using a rubber mallet to gently tap the boards into a flush alignment.
The final stage of the project is where the installation truly comes to life. Once all boards are secured, inspect the seam gaps; a consistent 1/16-inch gap is ideal for that authentic, rustic shadow line. If you prefer a tighter, more modern look, you can opt for minimal gaps, but be aware that this requires perfect substrate leveling. To finish, lightly sand the surface with 220-grit sandpaper to remove any splinters or manufacturing marks, taking care not to round over the crisp edges of the groove. Apply your chosen stain or paint, sealing the wood to protect it from moisture. By treating the wall as a canvas and correcting its unevenness with intention, you create a feature wall that feels both curated and natural.
To cut a gap in the shiplap, ensure your board (or two if the outlet will cross two boards) is already cut to the length it needs to be to fit on the wall. Then ...
🔨 How to Install Shiplap on a Wall - DIY - YouTube
13.09.2021 ... Is this drywall or plaster? If drywall and you're planning to put up shiplap, just rip it out.
Shiplap How To Apply How To Install Shiplap Over A Concrete Wall Fox
29.05.2021 ... Shiplapping one wall in a room looks best when you have no seams. Some people prefer the rugged farmhouse look with uneven shiplap that ...
How To Install a Shiplap Wall - YouTube
How To Shiplap A Curved Wall · 1/4” Maple Plywood (see details below) · Finishing molding for the side and top of the shiplap · GLOVES (absolute MUST or you will ...
How To Put Shiplap On Ceiling | Shelly Lighting
20.06.2023 ... 1/4 inch sheet of lauan plywood ripped into 4 inch strips works just as well. Sand edges of each cut lightly with a Sheet of sand paper. I use a ...
Can You Put Shiplap on Uneven Wall? (How To) - Ready To DIY
14.04.2023 ... The best wood to use for vertical shiplap is real shiplap boards that have a rabbet cut on them creating a nickel gap. However, to save money, 1 ...
Can You Put Shiplap on Uneven Wall? (How To) - Ready To DIY
02.01.2019 ... I live in a house that's over 100 years old. I have a kitchen wall that I want to shiplap or put peel & stick faux shiplap, ...
How To Hang Shiplap Horizontally at Phoebe Grieve blog
12.06.2021 ... Vertical shiplap adds texture and height to any room and can be installed over drywall without removing anything. This guide walks you ...
Step-by-Step Guide to Installing Shiplap on Walls for a Professional ...
17.07.2016 ... It works better with a small wall like the one in the bathroom picture. To answer your question you could start one row down and then scribe ...
Shiplap How To Apply How To Install Shiplap Over A Concrete Wall Fox
25.07.2022 ... To install shiplap correctly, it must be face nailed. Step Four: Nickel Gapping. After you have the first row installed the rest of the process ...
Step-by-Step Guide to Installing Shiplap on Walls for a Professional ...
white shiplap walls with woman doing handstand in front Shiplap Process Outline ... Putting up shiplap is a multi-step process that is time-consuming from ...
How To Install Shiplap In 4 Simple Steps Shiplap Wall
13.02.2026 ... We're on the last wall and it's so uneven that we can't do anything except cover it up. So basically, we just put furring strips to even out ...
How to Install Vertical Shiplap: Panels vs. Boards - Stefana Silber ...
STEP 1: CLEAR WALLS & USE STUD FINDER TO MARK THE STUDS · STEP 2: INSTALL FURRING STRIPS ON STUDS HORIZONTALLY · STEP 3: INSTALL SHIPLAP · STEP 4: CUT BOARDS WHEN ...
How To Install Shiplap On Existing Wall at Rae Johnson blog
Use a small nail to find the studs and then keep them in a straight line, so they are easy to see. The shiplap paneling will cover the lines, so there is no ...
How To Put Shiplap On Block Wall at Jonathan Rose blog
29.08.2025 ... If you want to install shiplap style paneling, keep watching! We're using our tongue and groove wall panels for this DIY, so the first step ...
15 Tips for a Perfect, Easy Shiplap Wall Install - YouTube
09.03.2021 ... Step 1: Clear Walls and Mark Your Studs · Step 2: Install Furring Strips on Studs Horizontally · Step 3: Install Shiplap · Step 4: Installing ...
Cheap and easy DIY shiplap wall tutorial. Learn how to make easy diy ...
16.07.2018 ... Great! Good luck and keep the string the same distance from the wall. You could use a Combination square to set and check the distance.
Can You Put Shiplap on Uneven Wall? (How To) - Ready To DIY
Method 2: Construction Adhesive · Prep your wall surface. Adhesive bonds best to smooth, clean, primed surfaces. · Mark your layout lines. Just like blind nailing ...
How to Hang Shiplap: Best Easy Tips for Beginners
13.11.2022 ... In this video, I show how to install shiplap on interior wall to create an accent wall. A shiplap install is a DIY project that any beginner ...
Can You Put Shiplap on Uneven Wall? (How To) - Ready To DIY
04.05.2026 ... I found my studs in the wall. and then I painted the edges and seams. as I put each board up. I use nickels as spacers. You can also use a ...
How to Install a Shiplap Wall in 4 Simple Steps | Shiplap wall diy ...