Cable Resistance Calculation Formula

Timothy Aug 03, 2026

The calculation of cable resistance is a crucial step in electrical engineering to ensure the safe and efficient operation of circuits. The resistance of a cable, or any conductor, is a measure of opposition to the flow of electric current and is expressed in ohms (Ω). The formula to calculate cable resistance involves several factors, which we will delve into in this comprehensive guide.

Cable Size Selection
Cable Size Selection

Before we dive into the calculation formula, let's understand why it's important. Cable resistance, along with current, determines the power loss (heat dissipation) in a cable. Too high a resistance can result in excessive heat, which may lead to cable degradation or insulation failure. On the other hand, too low a resistance might lead to excessive current flow, causing overheating at the load end. So, the cable resistance calculation is vital for designing safe and reliable electrical systems.

a piece of paper with writing on it that says calculating resistance everything has restores
a piece of paper with writing on it that says calculating resistance everything has restores

Cable Resistance Formula - Key Factors

The resistance of a cable is primarily determined by its length, cross-sectional area (or gauge), and material. The formula to calculate cable resistance is based on these factors:

How to Calculate Cable Size from kW
How to Calculate Cable Size from kW

R = (L * ρ) / A, where:

  • R is the resistance of the cable (ohms)
  • L is the length of the cable (meters)
  • ρ (rho) is the resistivity of the conductor material (ohm*meters) at a specific temperature
  • A is the cross-sectional area of the conductor (square meters)
Cable Sizing
Cable Sizing

Cable Length and Resistivity

Of these factors, length and resistivity are straightforward. Length (L) is simply the distance the cable conducts current. Resistivity (ρ), on the other hand, is the material's inherent resistance to electric current. Copper, a common conductor, has a resistivity of about 1.68 x 10-8 ohm*meters at 20°C.

To account for temperature changes, which affect resistivity, we can use the following equation for copper:

electrical calculations poster with diagrams and instructions
electrical calculations poster with diagrams and instructions

ρT = ρ0 * (1 + α * (T - T0))

where:

  • ρT is the resistivity at temperature T
  • ρ0 is the resistivity at temperature T0 (usually 20°C)
  • α is the temperature coefficient of resistivity (1/°C)
  • T is the operating temperature (°C)
Electrician World
Electrician World

Cable Cross-Sectional Area and Gauge

The cross-sectional area (A) of a cable is the area of its conductor. This is often determined by the cable's American Wire Gauge (AWG) or its gauge according to the particular standards of your region. The cross-sectional area for a solid circular conductor can be calculated as:

an electrical wiring diagram for the as / s cable size calculator
an electrical wiring diagram for the as / s cable size calculator
Download Electrical Cable Size Calculator Excel
Download Electrical Cable Size Calculator Excel
Cable Trench Design Calculation | Important Guide
Cable Trench Design Calculation | Important Guide
Electrical Wire & Cable Sizes with Current Rating ⚡ Cheat Sheet for Safe Wiring Guide
Electrical Wire & Cable Sizes with Current Rating ⚡ Cheat Sheet for Safe Wiring Guide
How to Calculate Cable Size for any Electrical Load?
How to Calculate Cable Size for any Electrical Load?

A = π * (D2 / 4)

where D is the diameter of the conductor. For a stranded conductor, this formula still applies, but the effective area is slightly less than the total area of the strands due to voids between them.

If the cable's gauge is known, you can convert this to a cross-sectional area using the following SWG (Standard Wire Gauge) formula for solid conductors:

A = 0.127 * (14 + 0.052 * n)2 / 4

where n is the gauge number and A is the area in square inches. To convert this to square meters, multiply by 6.4516.

Cable Resistance Calculation Example

Let's calculate the resistance of a 50-meter long, 16 AWG copper cable operating at 40°C.

First, calculate the cross-sectional area:

A = 0.127 * (14 + 0.052 * 16)2 / 4 * 6.4516 = 1.13 x 10^-6 m2

Then, calculate the resistivity at 40°C:

ρ40 = 1.68 x 10^-8 * (1 + 0.00393 * (40 - 20)) = 1.89 x 10^-8 ohm*meters

Finally, calculate the resistance:

R = (L * ρ40) / A = (50 * 1.89 x 10^-8) / 1.13 x 10^-6 = 0.79 ohms

So, the resistance of the 50-meter long, 16 AWG copper cable at 40°C is approximately 0.79 ohms.

Understanding and correctly applying the cable resistance calculation formula is crucial for electrical engineers. It determines the safety, efficiency, and durability of electrical systems. Regularly reviewing and applying this formula, along with other related electrical principles, helps maintain your expertise in the field. Stay curious and keep learning!