How to Calculate Strip Footing Size: A Comprehensive Guide

Timothy Aug 03, 2026

Calculating the size of strip footings is a critical step in the construction of any building or structure. The size and configuration of these footings directly impact the stability and longevity of your project. But how do you calculate strip footing size? This comprehensive guide will walk you through the process in a clear, step-by-step manner.

How to Calculate Board Feet or Linear Feet — Tyler Brown Woodworking
How to Calculate Board Feet or Linear Feet — Tyler Brown Woodworking

The process involves a few key parameters: load, soil properties, and strip footing dimensions. Let's dive into each of these, starting with understanding the loads your footing will bear.

the differences between linear feet and square feet are shown in two different sizes, with text describing
the differences between linear feet and square feet are shown in two different sizes, with text describing

Understanding Loads

Before calculating footing size, you need to know the load it will bear. This includes the dead weight of the structure above it, plus any future live loads (like furniture or people).

the size chart for millmeter to inch chart with measurements and instructions on it
the size chart for millmeter to inch chart with measurements and instructions on it

Dead loads are static loads that don't change over time, while live loads are dynamic loads that do. Both are crucial considerations when determining strip footing size. Let's look at how to calculate each.

Calculating Dead Loads

How to Design Plain Concrete Footing for R.C.C Columns as per Indian Standards?
How to Design Plain Concrete Footing for R.C.C Columns as per Indian Standards?

Dead loads are straightforward to calculate. They're essentially the weight of the structure itself, including all its materials and finishes. The formula is: Dead Load = Weight of Structure = Weight of Materials + (Volume of Structure × Material Density).

For example, if your wall is 10m long, 2.5m high, and made of concrete with a density of 2400 kg/m³, your calculation would be: Dead Load = (10m × 2.5m × 0.3m) × 2400 kg/m³ = 18,000 kg or 18 metric tons.

Calculating Live Loads

The Use of Waterbars or Waterstops for Water Retaining Structures - Basic Civil Engineering
The Use of Waterbars or Waterstops for Water Retaining Structures - Basic Civil Engineering

Live loads are more variable and depend on the type of structure and its intended use. For residential buildings, live loads might be as low as 1.5 kN/m², while for commercial buildings, they could be as high as 3-5 kN/m².

To calculate total live load, multiply the live load per square meter by the area of the floor: Total Live Load = Live Load per m² × Area of Floor.

Soil Investigation

Concrete Footing Calculator: Bags for Sonotubes & Piers
Concrete Footing Calculator: Bags for Sonotubes & Piers

Strip footing size also depends on soil properties. Thus, a thorough soil investigation is crucial. You'll need to know the soil's bearing capacity (q_f) in kN/m². This can be obtained from geological surveys or soil tests like Standard Penetration Tests (SPT).

With this information, you can calculate the safe bearing pressure (q_allow), which is usually around 50-70% of the soil's bearing capacity. This ensures adequate safety factors and accounts for any unforeseen loads.

How to Measure for Linear Feet (Free Calculator)
How to Measure for Linear Feet (Free Calculator)
Types of Stirrups : Uses, Objectives, Design Consi
Types of Stirrups : Uses, Objectives, Design Consi
the table shows how many different numbers are used to make this chart for each item
the table shows how many different numbers are used to make this chart for each item
The principal types of foundations
The principal types of foundations
HOW TO CONVERT METERS TO FEET
HOW TO CONVERT METERS TO FEET
a diagram showing how to read the length chart for different types of numbers and letters
a diagram showing how to read the length chart for different types of numbers and letters

Bearing pressure and safety factor

The bearing pressure is calculated as: Bearing Pressure = Total Load / Area of Footing. To find the area of the footing, you'll need to use trial and error, adjusting the footing's width and depth until the bearing pressure equals the allowable bearing pressure.

Remember to consider safety factors. A common safety factor (Fs) for strip footings is 3. Your final footing width (B) should be: B = 2 × (Load / Allowable Bearing Pressure × Fs).

Strip footing depth

The depth of strip footings (D) is usually taken as 300mm, but it can vary based on the soil's compressibility and the structure's load. If the soil is softer, a deeper footing is required to spread the load over a larger area and prevent excessive settlement.

Always consult with a structural engineer or architect for complex or critical projects. They can provide tailored advice based on your specific project's needs. Happy calculating!