Step-by-Step: Plumber Up Double Sink

Timothy Aug 03, 2026

Embarking on a home plumbing project like installing a double sink can be rewarding, not to mention significantly enhance your kitchen or bathroom's functionality. With the right tools, a bit of planning, and this comprehensive guide, you'll be well on your way to a successful installation.

How to Plumb a Double Sink: Things You Need to Know - Home Tips
How to Plumb a Double Sink: Things You Need to Know - Home Tips

Before you dive in, ensure you familiarize yourself with local building codes and obtain any necessary permits. Safety first, remember to turn off your water supply and electrical power to the affected areas. Now, let's dive into the process.

pipes and piping in an unfinished room
pipes and piping in an unfinished room

Gathering Tools and Materials

Having the correct tools and materials is half the battle. Here's a list to ensure you're well-equipped:

How to Change Double Sink to Single
How to Change Double Sink to Single
  • Tape measure
  • Pencil
  • Reciprocating saw
  • Hacksaw
  • Pliers
  • Soldering iron
  • Wire brush
  • Pipe wrench
  • Galeria-style faucet
  • Sink
  • Pipes and fittings (copper, CPVC, or PEX)
  • Plumber's putty
  • Teflon tape

Selecting the Right Sink and Faucet

the pipes are connected to the water heater
the pipes are connected to the water heater

Choosing a double sink and faucet set depends on your needs and aesthetic preferences. Consider size, material, and configuration. Common double sink designs include side-by-side, undermount, and drop-in. Faucets can be single handle, double handle, or hands-free.

Preparing the Installation Area

Measure your countertop or vanity to ensure your sink and faucet fit perfectly. Mark the drain hole and faucet hole locations. For undermount sinks, you'll need to cut a hole in the countertop. This can be done with a jigsaw or Hole Hawg tool.

How to Make a Double Sink in Your Home | Bathroom Remodel DIY
How to Make a Double Sink in Your Home | Bathroom Remodel DIY

Plumbing the Sink

Now that your workspace is ready, let's discuss the plumbing aspect of your double sink installation.

Installing the Pipes

Double Vanity Horizontal Drain Run Help
Double Vanity Horizontal Drain Run Help

Depending on your piping material, you'll use compression fittings, sweat joints (copper), or push-fit connections (PEX). Measure and cut your supply and drain lines, ensuring they're long enough to reach the faucet and sink but not so long that they kink or are difficult to work with.

Securing the Sink

the kitchen sink is connected to two separate piping lines, and labeled with instructions
the kitchen sink is connected to two separate piping lines, and labeled with instructions
How to Plumb a Double Sink With Garbage Disposal
How to Plumb a Double Sink With Garbage Disposal
a person's hand is holding the pipe for a wall mounted sink faucet
a person's hand is holding the pipe for a wall mounted sink faucet
Single to Double Sink Vanity (again)
Single to Double Sink Vanity (again)
How To Plumb A Double Kitchen Sink With Disposal And Dishwasher
How To Plumb A Double Kitchen Sink With Disposal And Dishwasher
Step-by-Step Dishwasher Drain Setup for Double Sink Plumbing
Step-by-Step Dishwasher Drain Setup for Double Sink Plumbing

For drop-in sinks, apply a layer of plumber's putty around the drain hole. Place the sink into position and press down firmly. For undermount sinks, secure the sink to the underside of the countertop using clips or brackets. Test the sink's stability; it should not rock or wobble.

Connecting the Water Supply

With the sink secure, it's time to connect the water supply.

Soldering Copper Pipes

If you're using copper pipes, follow these steps to solder the fittings:

  1. Clean the pipe and fitting using a wire brush.
  2. Apply flux to both the pipe and fitting.
  3. Slide the fitting onto the pipe, leaving about 1/4 inch of pipe showing.
  4. Heat the fitting and pipe using a soldering iron, then apply solder.
  5. Once the solder flows, remove the heat and allow it to cool.

Connecting Other Piping Materials

For CPVC and PEX, follow the manufacturer's instructions. Typically, you'll use compression fittings for CPVC and push-fit connectors for PEX.

Installing the Faucet

With the plumbing out of the way, it's time to cap off your project with the faucet installation.

Assembling the Faucet

Galeria-style faucets have two separate handles, one for hot and one for cold. Assemble the faucet according to the manufacturer's instructions, ensuring you install the hot and cold markings correctly.

Securing the Faucet

Apply plumber's putty around the faucet base. Place the faucet into the countertop hole and secure it with the locking nuts provided. Tighten gently to avoid cracking the countertop. Install the handles and aerator, then connect the faucet lines to your supply pipes.

Turn on your water supply and test your new double sink. If there are no leaks and everything works as expected, pat yourself on the back – you've just successfully plumbed up a double sink! Regularly maintain your sink and faucet to keep them in tip-top shape, and don't hesitate to call a professional if you encounter any issues beyond your skillset.