Installing a GAF Ice and Water Shield is a crucial step in ensuring your roof's integrity, especially in areas prone to ice dams and moisture. This latest generation, synthetic underlayment protects your roof from water damage and prevents leaks. Here's a comprehensive guide on how to install it like a professional.

Before we dive into the installation process, let's understand what GAF Ice and Water Shield is. It's a self-adhesive, synthetic roofing underlayment designed to provide an additional layer of protection against water intrusion. Unlike traditional felt underlayment, it doesn't tear or absorb water, and it adheres directly to the roof deck, creating a waterproof barrier.

Preparation and Initial Setup
Before you start, make sure you have all the necessary tools and materials. You'll need GAF Ice and Water Shield rolls, a roofing nailer with 1-1/4" roofing nails, a utility knife, a measuring tape, and a chalk line.

Next, ensure your roof deck is clean, dry, and free of any debris or contaminants. This will allow the underlayment to stick properly. If your roof has any damaged or rotted areas, repair them before proceeding.
Measuring and Laying Out the Field

Start by measuring your roof to determine how many rolls of GAF Ice and Water Shield you'll need. A standard roll covers approximately 2,600 square feet, but it's always a good idea to have extra material for(errors and waste.
-using a chalk line, snap a line across the roof near the lowest edge, where you want to start laying the underlayment. This line will serve as your guide for keeping the underlayment straight and even as you install it.
Installing the First Roll

Start at the bottom of the roof, near the eave. Unroll the GAF Ice and Water Shield, stretching it out across the roof. The peel-and-stick backing should be facing up. Align the leading edge with the chalk line you snapped earlier.
Press the leading edge firmly against the roof, then carefully peel back the release paper, starting at the top and working your way down. Remember to keep the roll straight and even, following the chalk line. Avoid walking on the underlayment as much as possible.
Installing Additional Rolls

Once you've installed the first roll, measure up the roof to determine the starting point for the next roll. GAF recommends overlapping each roll by at least 6 inches. Snap a chalk line at this point and install the next roll, following the same process as the first.
Continue installing rolls in this manner, working your way up the roof. Always ensure that the underlayment is overlapping the roll below it by at least 6 inches. This will create a waterproof barrier that can handle whatever weather comes its way.









Installing Around Obstacles
You'll encounter obstacles like vents and chimneys as you install the GAF Ice and Water Shield. To manage these, cut the underlayment to fit around the obstacle, then wrap it up the sides and seal it with roofing cement. Ensure that the underlayment overlays any flashing or counter flashing by at least 2 inches.
Hip and ridge caps will overlap the underlayment. No additional overlap is required at these points.
Securing the Underlayment
While the self-adhesive backing provides a good initial seal, it's crucial to secure the underlayment with roofing nails. Use a roofing nailer and 1-1/4" roofing nails to secure the underlayment along the leading edge and at intervals not exceeding 36" on center along the laps.
Be careful not to nail too close to the edge, as this can cause the underlayment to tear. Also, avoid nailing in the adhesive area, as this can cause the underlayment to peel off.
Final Inspection and Aftercare
Once you've installed the GAF Ice and Water Shield, inspect your work. Ensure that there are no tears, wrinkles, or missed areas. Also, make sure that the overlap is consistent and adequate across the entire roof.
After installation, the underlayment can be exposed to the elements for up to 6 months while you complete other aspects of your roofing project. However, it's important to keep an eye on it, especially during heavy rain or snow, to ensure that it's still intact and functional.
Regular inspections of your roof can help you detect any potential issues early, ensuring that your GAF Ice and Water Shield continues to protect your roof effectively for years to come.
And there you have it - a comprehensive guide to installing GAF Ice and Water Shield. Remember, a roof is only as good as its foundation, and the underlayment is a critical part of that foundation. So, take your time, follow these instructions carefully, and you'll have a roof that's ready to stand up to whatever nature throws at it. Safe installation!