Easy Grace Ice and Water Shield HT Installation Guide

Anna Aug 02, 2026

Enhance your roof's protection against ice dams and water intrusions with the Grace Ice & Water Shield HT. This advanced, self-adhering membrane is designed to safeguard your roof's critical areas, preventing water and ice from backing up under your shingles. Let's delve into the step-by-step installation instructions to ensure a secure and durable application.

ICE AND WATER SHIELD INSTALLATION TRICKS
ICE AND WATER SHIELD INSTALLATION TRICKS

Before we commence, it's crucial to understand that the Grace Ice & Water Shield HT is not a substitute for a proper roof installation. It's an additional layer of protection for vulnerable areas such as eaves, rakes, flashing, valleys, and penetration sites. Always commence with a structurally sound and well-ventilated roof.

Ice & Water Shield Calculator
Ice & Water Shield Calculator

Preparation and Materials

Gather your materials and tools. You'll need the Grace Ice & Water Shield HT, a sharp utility knife, roofing nails with wide heads (not included in the membrane package), roofing cement, and a caulking gun.

Home Improvement and Remodeling - This Old House
Home Improvement and Remodeling - This Old House

Inspect your roof. Ensure it's clean, dry, and free from any debris. If your roof is frozen, thaw the critical areas before installation to maintain membrane adhesion.

Installation on Roof Deck

What is Ice and Water Shield on a Roof? (Types, Cost, and More)
What is Ice and Water Shield on a Roof? (Types, Cost, and More)

Start by unrolling the Grace Ice & Water Shield HT on the roof deck. Ensure the membrane overlaps the edges of the deck by at least 6 inches. The overhang should extend beyond the eaves and drip edge metal.

Using roofing nails, secure the membrane to the roof deck. Space the nails about 6-8 inches apart, placing them within the slit grooves. Avoid nailing through the slit grooves to prevent membrane damage.

Installing at Eaves and Rakes

Grace Self Adhering Ice And Water Shield Ht
Grace Self Adhering Ice And Water Shield Ht

The primary function of the membrane at the eaves and rakes is to direct water and ice from the edges of the roof. Start at the eaves, positioning the membrane so it overhangs the edge of the roof by at least 2 inches.

Fold back the membrane on the rakes, positioning it so it extends up the slope at least 3 inches. Unfold the membrane, ensuring it remains tailed-in over the eaves. Overlap subsequent courses by at least 6 inches, securing them with roofing nails as before.

Handling Penetrations and Flashing

How to Install Ice Shield
How to Install Ice Shield

The Grace Ice & Water Shield HT can encapsulate most roof penetrations, such as vents, pipes, and chimneys. Always follow the penetration manufacturer's instructions when combining products.

To flashed a penetration, fold the membrane around the base, ensuring a tight seal. Seal any slits or cuts with roofing cement. Trim excess material, ensuring no membrane extends beneath the flashing.

How to install ice and water shield on the roof
How to install ice and water shield on the roof
Ice and Water Shield For Roofs: A Complete Guide - Today's Homeowner
Ice and Water Shield For Roofs: A Complete Guide - Today's Homeowner
a flat roof being installed on a house
a flat roof being installed on a house
Why Your Roof Needs Both Ice & Water Shield and Underlayment
Why Your Roof Needs Both Ice & Water Shield and Underlayment
the flat roof is being installed on this house
the flat roof is being installed on this house
the roof is being installed to protect it from falling snow and freezing up on top
the roof is being installed to protect it from falling snow and freezing up on top
an ice dam is shown with instructions on how to build it and what to use it
an ice dam is shown with instructions on how to build it and what to use it
BS4D: Ice Dam’s, Icicles & Attic Condensation, Oh My…
BS4D: Ice Dam’s, Icicles & Attic Condensation, Oh My…
ICE DAM PREVENTION: Watch Installation of Unique, Canadian-Made System
ICE DAM PREVENTION: Watch Installation of Unique, Canadian-Made System

Installing at Valleys

Valleys are critical roof areas where ice dams can form. Install the membrane at the valley, ensuring it extends at least 6 inches up each slope. Overlap subsequent courses by at least 6 inches, so the lower membrane extends over the upper membrane's end lap.

Weld the membrane to itself using an approved torch system for duration and drip edge metal. Follow the manufacturer's instructions for the specific Grace Ice & Water Shield HT product you're using.

Sealing End Laps

Sealing end laps is a crucial step to prevent water intrusion. Apply a generous bead of roofing cement along each end lap, spreading it evenly with a putty knife. Ensure no membrane slits are exposed and all cement is pushed into the slit.

The final application of roofing cement should be made after all other roofing work is completed and the membrane has fully adhered to the roofing surface. This step is crucial to ensure a watertight seal.

Congratulations! You've successfully installed the Grace Ice & Water Shield HT, reinforcing your roof's protecton against ice dams and water intrusions. Routine maintenance checks will ensure your roof's longevity and effectiveness, providing years of security against the elements. Happy roofing!"