The diameter of the hole is just as important as its location. For a 2x10 joist, which actually measures 1.5 inches by 9.25 inches in width, the hole diameter cannot exceed one-third of the depth of the joist. Since the depth is 1.5 inches, the maximum hole size is generally 1 inch. Drilling a hole larger than this compromises the fiber continuity of the wood, significantly reducing its ability to resist bending. Always verify this with specific engineering software or tables if using non-standard hole sizes.
Verification and Engineering

While a chart provides a general guideline, the final authority is the project’s specific engineering plans. Conducting a pull test or consulting a structural engineer is necessary if the standard rules do not align with the site constraints. Building inspectors will frequently check the hole placements during the rough-in phase to ensure they adhere to the chart guidelines. Double-checking measurements before cutting protects the contractor from liability and ensures the floor system passes inspection without delay.

Standard Spacing and Load Considerations
The standard spacing for 2x10 floor joists is either 16 or 24 inches on center, depending on the expected live load and the species of wood used. Before any drilling occurs, the joist must be sized and spaced according to the building’s design load. Local building departments will often require specific joist grades and span tables, which dictate the maximum distance a 2x10 can span without support. Hole placement is always secondary to the overall joist depth and width, as the hole itself creates a stress point that must be managed carefully.

Practical Application and Sibling Joists
In many residential builds, a 2x10 floor joist is paired with a 2x8 or another 2x10 to form a double joist. When this configuration occurs, the holes must be staggered. You cannot drill a hole directly on top of a hole in the adjacent joist; they must be offset by at least 6 inches horizontally. This staggering prevents a continuous void through the thickness of the floor system, which would create a weak link capable of failing under point loads from furniture or appliances.

The Three Rules of Holes
To maintain the structural capacity of a 2x10 joist, there are three fundamental rules regarding hole drilling that apply universally. First, the distance from the edge of the hole to the top or bottom of the joist must be at least 2 inches. Second, the edge of the hole must be no closer than 2 inches to the top or bottom edge of the joist. Third, holes cannot be drilled closer than 4 inches to the support at either end of the joist. These rules ensure that the remaining material surrounding the hole is sufficient to carry the shear and bending forces.
Diameter Restrictions

The diameter of the hole is just as important as its location. For a 2x10 joist, which actually measures 1.5 inches by 9.25 inches in width, the hole diameter cannot exceed one-third of the depth of the joist. Since the depth is 1.5 inches, the maximum hole size is generally 1 inch. Drilling a hole larger than this compromises the fiber continuity of the wood, significantly reducing its ability to resist bending. Always verify this with specific engineering software or tables if using non-standard hole sizes.
Position Relative to Other Holes and Features
If a joist requires multiple holes for plumbing or electrical runs, the spacing between these holes must also be calculated. Holes cannot be drilled within 2 inches of each other, creating a buffer zone for the material between the penetrators. Furthermore, if a hole is located in the middle third of the joist span, the restrictions are slightly more flexible than near the supports. However, drilling in the middle is generally discouraged for 2x10s used in floor systems due to the lower modulus of elasticity in that specific region.

Notches vs. Holes
It is important to distinguish between a drilled hole and a notched end. While a 1-inch hole might be permissible in the center of a 2x10, a notch at the end of the joist is treated differently. Notches are typically limited to 1/6 the depth of the joist and cannot be made in the top or bottom edge where bending stress is highest. If the utility runs require a significant opening near the support, it is better to sister a piece of wood or use a steel hanger rather than create a large notch, ensuring the load path remains uninterrupted.




















When designing a floor system, one of the most critical calculations involves determining where holes can be placed within a joist. For a common 2x10 dimensional lumber joist, understanding the specific limitations is essential for both safety and code compliance. This 2x10 floor joist hole chart serves as a quick reference for builders and engineers to ensure integrity is maintained.