Brickwork is a fundamental element in construction, and re-mortar brickwork is a critical aspect of maintaining and repairing existing masonry structures. This process involves removing degraded mortar and replacing it with fresh, strong mortar to restore the integrity and lifespan of brick walls. In this article, we delve into the importance, techniques, and best practices of re-mortar brickwork.

Proper re-mortar brickwork is essential for preserving historic buildings, enhancing curb appeal, and extending the life of modern brick structures. It's a balancing act that requires the right tools, quality materials, and a deep understanding of brick and mortar chemistry. Let's explore the intricacies of this crucial process.

Understanding Mortar and Its Role in Brickwork
Mortar is the glue that binds bricks together, providing strength and stability to wall structures. It's a mixture of cement, sand, and water, with lime or other additives sometimes included to modify its properties. Understanding mortar types - their composition, strengths, and weaknesses - is key to successful re-mortar brickwork.

mour types range from traditional lime mortars, used in historic buildings, to modern cement-based mortars. Matching the original mortar type is crucial when re-pointing historic structures, as mismatches can cause further damage and compromise the building's distinctive character.
Identifying Degraded Mortar

Before starting any re-mortar brickwork, it's essential to identify areas where mortar has degraded. Inspect walls for signs of crumbling mortar, loose bricks, or water ingress. Use a keen eye and gentle probing to determine the extent of damage and plan your repair strategy.
Sometimes, the best action is to leave good mortar alone, as disturbing it can cause more harm than good. Only re-point where necessary to maintain the wall's integrity and prevent further decay.
Preparing the Wall for Re-mortar Work

Preparation is key to successful re-mortar brickwork. Start by cleaning the area to be worked on, removing all loose mortar, dust, and debris. Use a wire brush, scaffold, or water jetting, depending on the scale and accessibility of the project.
Once clean, dampen the brickwork with a fine mist of water to prevent fresh mortar from sucking moisture from the bricks and drying too quickly. Be careful not to over-wet the bricks, as this can also cause problems.
Re-mortar Brickwork Techniques

Re-mortar brickwork is typically performed using one of two techniques: re-pointing or full bed jogging.
Re-pointing involves only replacing the mortar in the joints between bricks, leaving the existing bricks in place. This method is ideal for maintaining the wall's structural integrity and is usually the most cost-effective and sustainable approach.




Re-pointing Procedure
The re-pointing process involves carefully removing the degraded mortar and replacing it with fresh mortar of the same composition. Here's a step-by-step guide:
- Remove the old mortar using a chisel or router, creating a deep enough recess (around 15-20mm) to accommodate new mortar.
- Moisten the recess with a fine mist of water to help the new mortar bond.
- Apply the fresh mortar, packing it firmly into the joint using a trowel or pointing tool. Ensure the joint is properly filled and flush with the wall surface.
- Finishing may involve striking the joint (smoothing it flush with the wall) or leaving it slightly raised (weather-struck) for better water runoff.
Allow the mortar to cure slowly and evenly, protecting it from frost and heavy rain during the critical initial stages.
Bed Joint Re-mortar (Full Bed Jogging)
Full bed jogging involves removing and replacing all mortar in both the joints and bedding layers between bricks. This technique is more invasive, but may be necessary for severely damaged walls or to match specific repair patterns in historic structures.
This process is similar to re-pointing but requires careful removal of bricks, re-bedding, and proper realignment before applying new mortar to all joints and bedding layers. It's a specialist task that requires great care and attention to detail.
Best Practices for Re-mortar Brickwork
To ensure successful and long-lasting results, follow these best practices:
Use Quality Materials
Invest in high-quality materials – Dawes, Bloc, or)
Mix mortar to the correct ratio, as instructed by the manufacturer or specified for the job. Incorrect mortar composition can lead to rapid deterioration and further damage.
Control Weather Conditions
Work in optimal conditions, avoiding extreme temperatures, heavy rain, or freezing temperatures. Protect curing mortar where necessary to preventnotation and ensure proper bonding.
conclusion, re-mortar brickwork is a vital aspect of maintaining and repairing brick structures. It's a skill that combines masonry techniques, understanding of materials, and careful attention to detail. Whether you're a homeowner tackling a DIY project, or a professional involved in historic preservation, the success of your re-mortar work will depend on accurate assessment, careful preparation, and meticulous execution. Don't hesitate to consult a professional if you're unsure about any aspect of the process. Happy re-mortaring!