Installing a double sink is one of the most rewarding home improvement projects for any DIYer. Whether you are renovating a master bathroom or upgrading a kitchen, replacing a single fixture with two basins dramatically increases workflow and functionality. This guide walks you through the entire process, from shutting off the water to testing your new setup, ensuring a leak-free installation.
Assess Your Current Configuration
Before you purchase a new basin, you must understand the existing plumbing layout. Most standard installations connect to a 1 1/2-inch drain line, but variations exist. You need to verify the spacing between the current fixture holes and the center-to-center measurement, which is usually 8 inches for standard configurations. Measuring the water supply lines is also critical, as they must reach the new valves without being stretched or kinked.
Check Your Drain Assembly
Double sinks require a specialized waste assembly. A standard tailpiece connects to a T-fitting, which splits into two branches for the basins, converging into a single shared drain pipe. You will also need a waste lock nut and appropriate PVC or brass fittings. If your current setup uses a grid insulator or hair catcher, remove it to access the flange for easier disconnection.

Gather Tools and Materials
Success in plumbing hinges on having the right equipment on hand. Attempting a job with improvised tools often leads to stripped fittings and water damage. A methodical approach, combined with the correct supplies, minimizes stress and ensures a professional finish.
- Adjustable wrench or basin wrench
- Screwdriver set (flathead and Phillips)
- Plumber's tape or pipe dope
- Putty knife and rag
- Bucket or catch basin
- New double sink faucet
- Supply lines (if not included)
Turn Off the Water Supply
Safety is the first step in any plumbing project. Never assume that a valve is closed; always verify the water is completely stopped. You will need to isolate both the hot and cold lines leading to the fixture. Skipping this step results in immediate flooding, creating a messy and hazardous work environment.
Relieve Pressure
After turning the shut-off valves clockwise, turn on the existing faucet to drain the remaining water from the lines. This relieves pressure inside the supply tubes and prevents a sudden gush when you disconnect the lines. Keep the bucket ready to catch the residual water draining from the system.

Disconnect the Old Fixture
With the water off and pressure relieved, you can safely remove the old hardware. Use your wrench to loosen the supply lines at the valves and the mounting nuts securing the basin to the countertop. Be prepared for some resistance due to mineral buildup, but apply steady force rather than brute strength to avoid breaking the pipes.
Once the water lines are detached, unfasten the nuts securing the faucet handles and spout. Carefully lift the old fixture out of the sink holes. Now you will see the sink's mounting rim (the faucet body) that connects to the deck of the sink. Keep the old supply lines handy to use as a reference for length when installing the new faucet.
Install the New Double Sink Faucet
Installing the faucet is the most critical visual step of the process. You must thread the supply lines and mounting hardware correctly to ensure a secure fit. Most modern faucets come with washers or rubber gaskets that create a watertight seal against the sink deck.

| Faucet Component | Installation Note |
|---|---|
| Water Supply Lines | Wrap plumber's tape clockwise around the threads of the faucet's inlet to prevent leaks. |
| Faucet Body | Insert the faucet through the center hole of the deck plate before securing the mounting nut underneath. |
| Handle Valves | |
| Drain Assembly | Apply a bead of plumber's putty around the drain flange to seal the top of the sink. |
Connect the Water Supply Lines
With the faucet securely mounted, it is time to link the fixture to the home's plumbing. This requires careful threading of the flexible supply lines into the wall valves. Hand-tightening is recommended initially, followed by a final quarter-turn with a wrench to lock the connection in place.
Ensure the flexible lines are not twisted, as this creates stress on the fitting and leads to premature failure. The connections should feel snug but do not overtighten, as this can crack the valve seat or deform the copper tubing. Once connected, open the water supply slowly to allow pressure to fill the lines gradually.
Test for Leaks and Functionality
The final phase involves turning the water back on and observing the results. Before you activate the valves, double-check that the drain stoppers are removed and the sink is empty. Once the water flows, inspect every connection point with a flashlight. A slow drip indicates a loose fitting, requiring immediate adjustment.
After confirming there are no visible leaks, test the drainage speed. Run both basins simultaneously to ensure the shared plumbing can handle the volume without gurgling or backflow. If the sink drains slowly, you may need to adjust the P-trap or snake the drain to clear debris introduced during the installation process.



















