Removing a solid surface backsplash is a task many homeowners face during a kitchen remodel or when updating the look of their space. While it might seem daunting, the process is straightforward when you follow the right steps.

Unlike tile, which shatters and adheres strongly to mortar, solid surface materials like Corian or Hi-Macs are designed to be removed as a single sheet. This guide will walk you through the systematic process of safely detaching your old backsplash, protecting your cabinets and walls from damage in the process.

Preparing for Removal
Before applying any force, preparation is the most critical phase of this project. A solid surface backsplash is bonded tightly to the wall with adhesive, and rushing in with a hammer is a sure way to crack the material or dent the cabinets above.

Begin by clearing the area below the cabinets. Remove any hardware from the lower cabinets and take out the dishes, appliances, and cleaning supplies from the vicinity. If your countertop is still in place, you will need to remove it to access the bottom edge of the backsplash, which is often where the removal process begins.
Safety and Protection

Safety gear is essential for this type of demolition. Put on safety glasses to protect your eyes from debris and sharp edges. Additionally, wearing work gloves will provide a better grip and protect your hands from the abrasive surface of the old adhesive and any accidental chips in the material.
| Tool | Purpose |
|---|---|
| Putty Knife or Chisel | To break the bond at the substrate level. |
| Heat Gun | To soften the adhesive for easier removal. |
| Reciprocating Saw (with Sawzall blade) | For cutting through the material if it cannot be removed whole. |
| Shur-Form or Scraper | For aggressive removal of residual adhesive from the wall. |
Detaching the Upper Edge

Most solid surface backsplashes are adhered not only to the wall but also to the underside of the countertop. To remove it cleanly, you must first break this top seal.
Locate the seam between the bottom edge of the backsplash and the top of the countertop. Insert a heavy-duty putty knife or a chisel into this joint. Gently tap the tool down to create a gap large enough to fit the blade of a reciprocating saw. If you do not have a saw, a long-bladed oscillating tool is also effective for this cut.
Cutting the Adhesive Bond

Once you have access behind the upper edge, insert the saw blade horizontally. You do not need to cut extremely deep; your goal is to slice through the thin layer of adhesive bonding the backsplash to the countertop. Work slowly from one end to the other until the blade has separated the material from the cabinet frame.
Breaking the Vertical Bond

















With the top edge free, you turn your attention to the main vertical surface. The material is likely still stuck to the wall with strong adhesive, but it should not require excessive force if done correctly.
Start at the top corner and gently pull the sheet away from the wall. If the material resists, do not yank it. Instead, use a heat gun to target the edges and middle of the sheet. The heat will break down the polymer-based adhesive, causing the sheet to loosen. As the adhesive softens, you should be able to peel the backsplash down the wall relatively easily.
Handling Corners and Outlets
When you reach an electrical outlet or a sharp inside corner, proceed with caution. Outlets need to be removed from the circuit and unscrewed before pulling the sheet away from the wall. For corners, score the material carefully with a utility knife to prevent it from cracking or snapping under pressure.
Removing Residual Adhesive
Assuming the solid surface came down in one piece, the job is nearly complete. However, the wall underneath will likely be covered in a thick layer of cured adhesive.
For a smooth surface ready for new installation, you must strip this old glue. A Shur-Form scraper or a sturdy putty knife is the best tool for this job. Stand on a stable ladder and scrape parallel to the wall to remove the bulk of the adhesive. Be mindful not to gouge or sand the drywall or plaster beneath, as you will need a flat surface for the new backsplash.
Preparing for the New Installation
With the old material and adhesive gone, it is time to prepare the substrate for the new backsplash. Inspect the wall for any damage caused during the removal process. If the drywall is water-damaged or crumbling, you will need to patch and replace those sections before proceeding.
Once the wall is sound and clean, measure the new dimensions. Even though the cabinet heights haven't changed, it is vital to verify the measurements to ensure a perfect fit for your new solid surface sheets.
Finally, apply the new adhesive using a notched trowel, aligning the first sheet carefully. Because the surface is smooth and non-porous, solid surface installations require specific adhesives designed to maintain a tight bond without visible seams. Following these steps ensures a professional finish that will last for years.