Hyundai Venue Jack Points: Maximize Rewards with Expert Insight

Unlock exclusive value with Hyundai Venue Jack Points—your gateway to smarter rewards through smart driving and smart choices.

Jack Points are part of Hyundai’s loyalty program designed to reward frequent Venue owners with redeemable points. Earned through milestones like service anniversaries, referrals, and purchases, these points unlock discounts, free maintenance, and premium upgrades tailored to enhance your ownership experience.

Maximize your Jack Points by staying consistent with service schedules, referring friends, and participating in Hyundai events. Each refuel, scheduled check-up, and referral contributes directly to your growing reward balance—turning everyday actions into tangible benefits.

Redemption is seamless—use Jack Points for service exemptions, free vehicle inspections, access to exclusive Hyundai events, and even premium accessories. The flexibility ensures every point brings real value, deepening your connection with the Hyundai Venue brand.

Hyundai Venue Jack Points aren’t just a rewards program—they’re a strategic advantage for savvy owners. Start earning, redeeming, and enjoying smarter value today. Visit your nearest Hyundai Venue location or online portal to begin your Jack Points journey now.

Learn how to jack up, find the jack location and jacking points in a 2020 Hyundai Venue SEL 1.6L 4 Cyl. So i've been wanting to jack up my car to change the brakes however if i jack up from the pinch welds (which id prefer not to do) there is no room to fit a jack stand. The underbody is completely covered in the front of the car so it's hard to see a strong point there to jack from that's not the.

This is a guide on how to jack up your car properly. A Jack ALWAYS put your vehicle in gear and lock your E-brake when jacking your vehicle up, and use jack stands. Photos of the jacking points Pictures explaining how to jack up your car with a floor jack Note: You should use jack stands in pairs and never go further then 2 clicks from the end.

Always use the steel re. The front subframe and rear crossmember are recommended as valid lift points by Hyundai if you've got a hydraulic floor jack. They've got a document on hyundaitechinfo.com called "Lift Points and Precautions for Lift" that you can download that shows the best lift points and procedures for various types of lifts.

2021 Hyundai Venue, what do I use as a rear center jack points? I was doing an oil change for my gf, and we wanted to rotate her tires too, but I'm not sure where to put my floor jack in the rear, so that I can get it on stands. Jack label Model Name Maximum allowable load Always apply the parking brake before using a jack. Always turn off the engine before using a jack.

Never put any portion of your body under the vehicle supported by a jack. Only use the designated jacking locations on the frame. When supporting the vehicle, have the base plate of the jack flat on the ground under the lifting point.

Shift the gear. It is super clear where to put the jack. It has 2 prominent notches, and the jack goes in between them, and the jack has a slot for the pinch weld.

It is the most clearly marked jacking point I ever encountered on a vehicle. And of course, the compact spare only had 36 PSI, so I had to make a trip up the street to the gas station and drop $2. View, print and download for free: jack points - HYUNDAI VENUE 2023 Owners Manual, 390 Pages, PDF Size: 5.37 MB.

Search in HYUNDAI VENUE 2023 Owners Manual online. I would like to do my own oil changes (2015 Limited 2.4L), but I'm having difficulty figuring out a good place to jack up the front. I understand the factory pinch welds are the right places for the jack stands, but what about the actual jack itself? Is there a designated front jacking point.

The other alternative is to put jack stands at the pinch welds by using the floor jack in a place other than a factory approved location. But nobody has said where those points might be. Obviously you are taking a risk with using such points.

What I would like to find out from people on the forum, has anybody actually managed to do it successfully?