Converting a double sink into a single sink is a practical home improvement project that can streamline your daily routine and update the look of your bathroom or kitchen. This process involves removing one basin from the configuration and sealing off the plumbing that once served the unused side. While it requires a careful approach to drainage and water lines, the end result is a more spacious and efficient setup.

Understanding the Project Scope

Before beginning, it is essential to recognize that this is not merely a cosmetic swap; it is a plumbing reconfiguration. You are effectively changing the drainage system from two outlets to one, which means the trap and waste line need to be modified. Additionally, you will need to cap or remove the water supply valves that served the now-removed faucet. The success of the project hinges on accurately cutting the hole for the new basin and ensuring a watertight seal for the drain.
Preparation and Safety

Safety and preparation are the cornerstones of a smooth transition. You should gather all necessary tools, which typically include an adjustable wrench, a reciprocating saw or hacksaw, plumber’s putty, and a new single-hole faucet. Shutting off the water supply is non-negotiable. Locate the hot and cold valves under the sink and turn them clockwise until they are fully closed. Placing a bucket and old towels beneath the pipes will catch residual water and prevent a mess during the initial disassembly.
Shutting Down the Water

After turning the valves, open the faucets to release any remaining pressure and water in the lines. Because double sinks often share a single hot and cold supply line that splits to reach both fixtures, you will need to disconnect the riser pipes. This is the point where you must decide whether to keep the existing valves for the single remaining sink or replace the entire setup with a new valve assembly. If you are keeping the existing valves, ensure the lines feeding the removed sink are properly capped.
Removing the Old Configuration
With the water off and the pipes dry, you can unmount the faucet and sprayer. Disconnect the supply lines from the valves and the faucet. At this stage, you will see the double sink strainers and tailpieces connected to a shared waste line. To remove the basin, you may need to loosen the clips or brackets securing the countertop to the wall. If the sink is an undermount style, you might require a helper to support the weight while you detach it to avoid damaging the countertop surface.

Cutting the Opening
Installing the new single basin requires precise cutting if the existing hole is too large. If your new sink does not perfectly align with the old cutout, you will need to patch the old hole and create a new one. For laminate or solid surface countertops, a template provided by the sink manufacturer is vital to ensure the cut is accurate. Using a jigsaw with a fine-tooth blade, carefully follow the lines to create a clean, tight fit that supports the rim of the new sink.
Plumbing the New Drain

The most critical aspect of this conversion is the drain assembly. A double sink uses a T-shaped tailpiece that connects both basins to the trap. For a single sink, you need a simpler configuration. Remove the old tailpiece and install a new one that connects directly to the strainer. The trap should be positioned to allow enough slope for gravity to pull the water away without creating a siphon. Hand-tighten the connections initially, then use a wrench to secure them, ensuring they are snug but not overly forced, which could crack the pipes.
Connecting the Faucet




















Mounting the new faucet is generally straightforward, as most modern faucets are designed for single-hole installations. Feed the faucet tails through the center hole of the sink and secure them with the provided washers and nuts from underneath. Once the faucet is seated firmly, reconnect the supply lines. It is recommended to replace the rubber washers on the valves if they are old or brittle to prevent future leaks. Slowly restore the water supply and check the base of the faucet for any immediate seepage.
Testing and Finishing Touches
After all connections are made, turn the water back on fully and inspect the entire under-sink area. Look for drips or moisture around the pipes and the base of the faucet. Run the water for a few minutes, checking both the hot and cold functions, and then activate the garbage disposal if one is present. Finally, apply a bead of plumber’s putty or silicone around the edge of the sink where it meets the countertop. This final step ensures a clean look and provides a barrier against water intrusion, completing the transformation efficiently.