Installing under eave lighting is one of the most effective ways to transform the appearance and functionality of your home at night. This technique, often referred to as cove lighting, washes the exterior walls in a soft, ambient glow, highlighting architectural details and dramatically improving curb appeal. Unlike harsh spotlights, under eave lighting provides a subtle, sophisticated effect that enhances security and creates a welcoming atmosphere for evening gatherings.

The primary goal of this guide is to walk you through the entire process of installing under eave lighting, from initial planning to final connection. Whether you are a seasoned DIY enthusiast or a cautious beginner, understanding the specific steps involved will ensure a safe and successful project. We will cover essential topics such as fixture selection, electrical planning, and weatherproofing to give you the confidence to tackle this upgrade.

Planning Your Under Eave Lighting Layout
Before you purchase a single component, careful planning is essential to determine the best layout for your specific home. The ideal placement is directly underneath the eave, where the roof overhang meets the wall, creating a concealed light source that hides the fixture hardware. You should measure the total length of the area you wish to illuminate and decide whether you want continuous light or a segmented look with specific focal points.

Consider the architectural style of your house; a modern home might benefit from sleek, linear LED strips, while a traditional home may look better with discreet, low-profile fixtures. Sketching a simple diagram of your roofline and marking the intended fixture locations will help visualize the final result and ensure an even distribution of light across the surface.
Choosing the Right Fixture Type

Selecting the correct fixture is arguably the most critical decision in this project. Recessed LED "bricks" or low-voltage can lights are popular choices for their clean installation and focused beam, while flexible LED strip lights offer the advantage of conforming to irregular angles without requiring multiple junction boxes. For most residential applications, opting for a 12V low-voltage system is highly recommended due to the increased safety and flexibility it provides.
| Fixture Type | Best For | Installation Complexity |
|---|---|---|
| Recessed LED Brick | Modern looks, sharp beams | Medium (requires precise cutting) |
| Flexible LED Strip | Custom contours, tight spaces | Easy (adhesive backing) |
| Mini Can Light | Wide area coverage | Medium to High |
Gathering Tools and Safety Equipment

Assembling the right tools beforehand will streamline the installation process and prevent frequent trips to the hardware store. You will need standard electrical tools such as wire strippers, a voltage tester, screwdrivers, and a drill with appropriate bits for masonry or wood. Depending on your mounting location, you may also require a ladder stabilizer and extension ladders to access the eave safely.
Safety is paramount when working with electricity at heights. Ensure you wear insulated gloves and use a properly grounded electrical box. If you are installing into masonry, a hammer drill with a masonry bit is necessary, while wood installations require screws designed for exterior use. Always turn off the power at the circuit breaker and verify with a tester that the wires are dead before beginning any connection.
Installing the Mounting Hardware

For a seamless finish, the mounting bracket or housing must be secured directly into the structural members of your home, typically the wall studs or ceiling rafters. Using a level, mark a straight line where the fixtures will sit, and carefully drill pilot holes for the anchors. If you are installing into brick or stucco, use appropriate wall anchors designed for the weight of the fixtures and the weather conditions.
When attaching the housing, ensure it is flush with the underside of the eave to prevent water from pooling on the surface. Use corrosion-resistant fasteners, such as stainless steel or coated screws, to ensure the longevity of the installation. This step is crucial because it provides the physical support needed to hold the weight of the lights securely for years.




















Wiring and Electrical Connection
Running the electrical wiring requires careful consideration to maintain a clean appearance and comply with local building codes. You will need to run low-voltage wiring from the transformer to each fixture in a parallel circuit to ensure that one failed light does not affect the others. When routing the wires, use proper conduit or wiring clips to keep them secure and hidden from view, avoiding places where they might be exposed to the elements.
Connect the wires according to the manufacturer’s wiring diagram, typically involving matching positive to positive and negative to negative wires. It is vital to use waterproof wire nuts or heat-shrink butt splices to seal the connections against moisture. Once connected, place the transformer in a dry, ventilated area, often near the circuit breaker box, and test the system before finalizing the fixture placement.
Weatherproofing and Final Touches
Because under eave lighting is exposed to rain, snow, and temperature fluctuations, sealing every junction and fixture housing is non-negotiable. Apply a high-quality silicone sealant around the edges of the fixtures where they meet the wall surface to prevent water intrusion. Ensure that all wire entry points are sealed tightly to protect the internal components from condensation and corrosion.
Finally, turn the power back on and perform a thorough test of the lighting system. Adjust the angle of the fixtures if necessary to achieve the desired wash effect on the wall. By following these meticulous steps, you will have successfully installed durable and beautiful under eave lighting that enhances your home’s aesthetic for many seasons to come.