Installing a utility sink faucet might seem like a daunting task reserved for seasoned plumbers, but it is one of the most rewarding DIY projects for any homeowner. This essential fixture, often subjected to heavy use for laundry, gardening, and general cleanups, requires a secure and leak-free installation to function properly. With the right tools, a bit of patience, and this guide, you can replace or install a new faucet with confidence, saving both time and money on professional service calls.
Gathering Your Tools and Materials
Before you turn a single valve, preparation is key to a smooth installation process. Rushing to the store mid-job is frustrating and breaks your momentum. Having a well-stocked toolkit ensures you have everything needed to complete the task efficiently and correctly.
You will need a specific set of tools to loosen the old connections and secure the new ones. These tools are designed to grip, turn, and seal without causing damage to the delicate chrome or brass finishes of your new fixture.

Essential Toolkit
- Adjustable wrench
- Channel-lock pliers
- Screwdriver set (flathead and Phillips)
- Teflon tape (PTFE tape)
- Pipe thread sealant
- Bucket or basin
- Towels or rags
Shutting Off the Water Supply
The most critical safety step in any plumbing project is cutting off the water supply. Attempting to install a faucet without doing this is a recipe for a soaked bathroom or laundry room, and potential water damage. You must ensure that water cannot flow to the sink while you work on the lines.
Most utility sinks have dedicated shut-off valves located behind the unit, similar to kitchen or bathroom sinks. If your sink does not have these valves, you will need to turn off the main water supply to the house. Once the valves are closed, turn on the faucet in the sink to drain the remaining water from the lines and relieve the pressure.
Removing the Old Faucet
With the water successfully shut off and drained, you can begin the removal process. Disconnecting the old faucet gives you access to the water lines and the mounting nuts that secure the fixture in place.

Start by disconnecting the supply lines from the valves. Use your wrench to loosen the nuts connecting the hot and cold lines. Be prepared for a small amount of residual water to spill out, which is why the bucket and towels are essential. Once the supply lines are free, you will need to loosen the mounting nuts located underneath the sink’s rim to lift the faucet body out of the deck.
Preparing the Deck and New Hardware
With the old faucet removed, you have a clear view of the installation area. This is the perfect opportunity to clean the deck surface and inspect the condition of the gaskets and washers. A clean surface ensures a better seal for the new fixture.
Unpack your new utility sink faucet and compare the new components to the old ones. Utility sink faucets often come with a rubber or neoprene gasket and a large locking nut. Apply a generous amount of plumber’s putty or a rubber gasket to the underside of the faucet base where it will sit on the sink deck. This prevents water from seeping down into the cabinetry beneath the sink.
Connecting the Water Supply Lines
Before threading the flexible supply lines back to the faucet, you need to prepare the connection points. Wrap the male threads on the faucet's inlet valves and the female threads on the wall valves with Teflon tape. This tape acts as a barrier, filling microscopic gaps and creating a watertight seal that prevents leaks.
Hand-tighten the supply lines first to ensure the threads align correctly. Using your wrench, snug the connections firmly. The goal is to be tight enough to prevent movement and dripping, but you must avoid overtightening, which can strip the metal or crack the valve seats.
Securing the Faucet and Testing
With the supply lines attached, you can now position the faucet through the deck of the sink. Align the holes carefully and gently lower the fixture into place. From underneath the sink, thread the mounting nut onto the stem and tighten it securely by hand. Use your channel-lock pliers to grip the locking nut and ensure the faucet base is flush against the deck.
Once the mounting is secure, it is time to turn the water back on. Slowly open the supply valves and watch the connections for any immediate drips. If you spot a leak, turn the water off immediately, tighten the fitting slightly, and test again. Allow the water to run for a minute to flush out any debris that may have entered the lines during the installation process.