23.02.2017 ... I have seen a few versions of this little Splayed Leg Table and I have always loved the design, it's simple, clean and a useful little table ......
Creating splayed table legs is an essential skill for any woodworker looking to add a touch of elegance and stability to their furniture. Splayed legs not only enhance the aesthetics of a table but also provide better support and prevent wobbling. In this guide, we'll walk you through the process of making splayed table legs, from understanding the basics to the final sanding and finishing touches.
Splayed table legs are cut at an angle, typically between 10 to 15 degrees, which creates a wider base for the table. This design feature provides better stability, especially for larger tables. The angle also adds visual interest, making the legs appear lighter and more graceful.
Selecting the right wood is crucial for creating durable and attractive splayed table legs. Hardwoods like maple, oak, or cherry are excellent choices due to their strength and aesthetic appeal. Avoid softwoods as they may not hold up to the stress of splaying.

Before you start cutting, you need to determine the angle and length of your splayed legs. The angle depends on the desired look and the size of your table. A good starting point is 12 degrees. To calculate the length, measure the height of your table and subtract the thickness of your tabletop. Then, use the Pythagorean theorem to find the hypotenuse (the length of the leg).
| Table height (H) | Tabletop thickness (T) | Desired angle (A) | Leg length (L) |
|---|---|---|---|
| 30 inches | 1.5 inches | 12 degrees | 29.9 inches |
Once you have your measurements, it's time to cut the legs. If you're using a table saw, set the blade angle to your desired degree. If you're using a miter saw, you'll need to calculate the angle based on the blade's bevel setting. Cut one leg at a time, ensuring you maintain the same angle for all legs.
After cutting, you'll need to assemble the legs. If your table has aprons, attach the legs to them using wood screws. If not, you'll need to create a support structure or use stretchers to connect the legs. Apply wood glue to the joints before screwing to ensure a strong bond.

Once the legs are assembled, sand them thoroughly to remove any rough spots. Start with 120 grit sandpaper, then switch to 220 grit for a smooth finish. After sanding, apply your chosen finish. This could be a stain to enhance the wood's natural grain, paint for a bold look, or a clear sealant to protect the wood.
Creating splayed table legs is a rewarding skill to master. It allows you to add a personal touch to your furniture and ensures your table is both stable and stylish. With practice, you'll find that making splayed table legs becomes second nature, opening up a world of design possibilities.
<strong>Make a Splayed Leg Side Table - YouTube</strong><p>23.02.2017 ... I have seen a few versions of this little Splayed Leg Table and I have always loved the design, it's simple, clean and a useful little table ...</p>
<strong>Building a splay-legged table with hand tools - David Walbert</strong><p>28.07.2019 ... Splaying the legs means that the aprons are pulled outward off square, and so you have to plane the long ends at an angle to meet the tabletop.</p>
<strong>Splay-Legged Table - FineWoodworking</strong><p>Because of the taper and splay of the legs, a three-dimensional leg pattern will prove useful and will ensure uniformity. To make the pattern, lay out pleasing ...</p>
<strong>Creating Splayed Leg Joinery for a Mid-Mod Dresser - YouTube</strong><p>24.10.2025 ... Learn how to create precise, angled joinery with Shaper Origin. In this Session, we'll walk through the process of creating clean, ...</p>
<strong>Making a Splayed Leg Side Table</strong><p>Making a Splayed Leg Side Table ... I stared off with the legs that were 25 inches long and 1.25 inches square. I set these up on my tapering jig on my table saw ...</p>
<strong>Making a Splay-legged Stool: Part I - Paul Sellers' Blog</strong><p>20.04.2025 ... I cut and planed my legs to size, paired them up for looks, and then laid out for two frames to create two frames only. The holes receiving the ...</p>
<strong>Making a Cricket Table - Woodworkers Institute</strong><p>For example a wide splay over a short distance, i.e. short legs, will make your table appear more squat and put stress on the joints at the apron if a bottom ...</p>
<strong>Splay-Legged Table - Fine Woodworking</strong><p>Make a pattern to lay out all four legs. Because of the taper and splay of the legs, a three-dimensional leg pattern will prove useful and will ensure ...</p>
<strong>Splay Leg Table : r/BeginnerWoodWorking - Reddit</strong><p>04.11.2024 ... Glue up for the table top was with a hand plane since I didn't have a jointer. I cut a rough taper on the legs with a bandsaw and then a ...</p>
<strong>Making a Raked and Splayed-Leg Stool or Stand - YouTube</strong><p>30.08.2017 ... Comments ; Stool - Cut Legs to Length. Brad “The Wood Hunter” Unger · 7.4K views ; Make a Splayed Leg Side Table. WoodWorkWeb · 13K views ; Foolproof ...</p>
<strong>Splay Legged Table 4: Finished - JKM Woodworking</strong><p>24.03.2024 ... I plan to make a coffee table with splayed legs, and this project was about working out the details of the angled aprons mating with the splayed legs.</p>
<strong>How to make sturdy splayed legs on a bed? - Facebook</strong><p>26.02.2026 ... Three-legged bedside table design with storage access. Brad Curtis ▻ Woodworking For Beginners. 2y · Public.</p>
<strong>Attaching splayed (angled) legs to apron - Woodworking Talk</strong><p>13.02.2024 ... The angles, lay the legs on a table or sheet of plywood at the angle that appeals to you. Then either use a miter gauge on the plywood to see ...</p>
<strong>How to Make Table Legs Out Of 4x4? Pro Guide 2026</strong><p>08.12.2025 ... Drill two or three dowel holes per apron end. Use a jig for perfect alignment. · Domino or loose tenons speed things up. Great strength with less ...</p>
<strong>Splay Legged Table Step #1 - YouTube</strong><p>01.09.2020 ... Step #1 for building the Splay Legged Table. Getting a board cut for the long and short sides.</p>
<strong>The trouble with Splayed Legs - Big Sand Woodworking</strong><p>10.12.2023 ... The biggest issue that arises with splayed leg stools (or other structures) is what happens to the horizontal cross-section of the leg as it is ...</p>
<strong>Splayed Leg Side Table - Philadelphia Furniture Workshop</strong><p>... made furniture. Through discussions and hands-on work, participants will make a small table with splayed, tapered legs using proven techniques and joinery ...</p>
<strong>Beginner question: Splayed leg angles - LumberJocks</strong><p>21.09.2018 ... just set your miter saw at 10 degrees, and make a stop so you cut them all the same length.</p>
<strong>Makes Legs Four-of-a-Kind and Flush to the Floor - WOOD Magazine</strong><p>07.08.2017 ... Put your project on a flat surface, such as your tablesaw top as shown at top. In a piece of 1⁄4 " plywood, cut a hole larger than the ...</p>
<strong>joinery - What is the strongest join for splayed legs?</strong><p>19.10.2015 ... I intend to make a splayed leg dining room table similar to the ones in these images: ... Because dining room tables typically support a good deal ...</p>