Understanding Timber Span Tables: A Comprehensive Guide
Timber span tables are invaluable tools for structural engineers, architects, and builders, providing quick and reliable calculations for the safe use of timber in construction. However, reading and interpreting these tables can be a daunting task for those new to the field. This guide aims to demystify timber span tables, helping you navigate them with confidence.
Understanding the Basics
Before delving into the tables, it's crucial to understand the key factors that influence timber's strength and stiffness:
- Species: Different timber species have varying strengths. For instance, hardwoods like oak are stronger than softwoods like pine.
- Size: Larger sections of timber can span further than smaller ones due to their greater strength and stiffness.
- Grade: Timber is graded based on its strength and stiffness. Higher grades can span further than lower ones.
- Loading: The amount and type of load (dead, live, wind, etc.) significantly impact the span.
Navigating Timber Span Tables
Timber span tables typically present data in a grid format, with columns for timber size, species, grade, and load, and rows for span lengths. Here's a simplified example:
| Size (mm) | Species | Grade | Load (kN/m) | Span (m) |
|---|---|---|---|---|
| 100x50 | Pine | C16 | 1.0 | 2.5 |
| 150x50 | Pine | C16 | 1.0 | 3.2 |
Reading the Table
To find the safe span for a given timber size, species, grade, and load, follow these steps:
- Locate the correct timber size in the first column.
- Move across to the correct species and grade.
- Find the load that matches or is closest to your intended load.
- Read the corresponding span length.
Interpreting the Results
The span length given in the table is the maximum safe span for the given timber under the specified load. If your required span is longer, you'll need to increase the timber size, grade, or reduce the load.
Factors to Consider
While timber span tables provide a quick and reliable starting point, there are additional factors to consider:
- Support conditions: The table assumes simple supports. If your timber is continuous or has other support conditions, you may need to adjust the span.
- Slope of the span: The table assumes the timber is horizontal. If it slopes, you may need to adjust the span.
- Combined loading: The table assumes the load is uniformly distributed. If the load is concentrated or combined with other loads, you may need to adjust the span.
Conclusion
Timber span tables are powerful tools that can save you time and ensure the safety of your structures. By understanding how to read and interpret these tables, you can make informed decisions about the timber you use in your projects. Always remember, however, that these tables are guides, and the final design should be checked by a qualified engineer.
More Details
You just read the numbers under the appropriate column heading. For example: A select structural, southern pine 2×8 floor joist has a 2650 Fb. While the same ...
08.07.2022 ... Originally I found 70x45mm timber which I thought should okay for the joists given it's hardwood F27 but I can't find a span table to work it ...
03.06.2019 ... Sizing timber Part 2 Span tables. Using span tables from AS1684 to calculates timber sizes.
Design Criteria and Loading. The spans given in these tables have been developed by experienced timber design engineers in accordance with.
12.11.2024 ... Did you know that accurately interpreting lumber span tables is fundamental to ensuring structural integrity and safety in your structural ...
12.09.2025 ... Four Steps to Reading LVL Span Tables · Choose the beam size – Find the depth and width of the LVL member you plan to use (e.g. 90×45 mm). · Set ...
... span tables and are calculated to the same standards. This table uses commonly available UK regularised timber depths. Read the notes at the bottom of the ...
Tables, such as those for rafters, floor joists and ceiling joists require the spacing of members to be known or selected in order to obtain the required size ...
13.11.2024 ... Then check the timber material. Look for the timber grade, such as MGP10, F7 hardwood, or LVL (Laminated Veneer Lumber). Next find the timber ...
The following is a guide for the most common sizes. COMMON TIMBER SIZES FOR A GIVEN SPAN ... > Read More. 18/12/25 What to do if your Registered Building ...
The spanning capacity of load-bearing members is determined by a combination of stress grades and timber sizes and product engineering. Span tables allow users ...
18.02.2022 ... All rafters are shown as blue and the table in blue must be read to find the timber size. Make sure that the headings are correct, (sheeting or ...
27.05.2019 ... Sizing timber. Part 1 - Terminology. Spans, spacing's, cantilevers, load widths. ... Sizing timber Part 2 Span tables. Matt the Chippie Trainer• ...
... tables, provides examples of how to read the table values, and other important information about the proper application of Southern Pine joists and rafters.
03.01.2005 ... Size your deck beams and headers with our easy-to-use span table, which allows you to cross reference the post spacing and joist length to ...
19.05.2024 ... There aren't really any span tables for beams, because it's so situational and you have to calculate the load for each application independently.
Read about how we use cookies and how you can control them by clicking "Cookie Settings." If you continue to use this site, you consent to our use of ...
23.05.2016 ... it important for every trade person to understand the need to span and space materials correctly. Today we walk over spacing and spanning ...
Grades include C16 and C24. 2. Strength graded timber is marked with stamps indicating grade. If timber is cut after grading, its grade is destroyed and ...
meyPINE3 is available in both structural and non-structural sections, this guide provides span tables for common loading scenarios using the structural section ...
