For anyone who has ever experienced the unsettling shudder and loud thump of a washing machine walking across the kitchen floor during the spin cycle, the solution is often simpler than a service call. A washing machine on a pedestal is not just a storage solution; it is a platform that elevates the appliance to a more ergonomic height, reducing back strain and making loading far easier. However, if that pedestal is even slightly uneven, the consequences can be noise, vibration, and potential damage to the machine over time. Leveling a washing machine on a pedestal is a fundamental skill that ensures the appliance operates safely, efficiently, and quietly for years to come.
The Critical Link Between Pedestal Stability and Machine Performance
Before diving into the adjustment process, it is essential to understand why this specific setup demands precision. Unlike a standard top-loading machine sitting directly on a floor, a pedestal lifts the washer to a comfortable working height. This elevation essentially turns the machine into a high-speed centrifuge; during the spin cycle, thousands of revolutions per minute generate significant force. If the load is not perfectly balanced across the drum, the machine will shift. On an unlevel pedestal, this shift is amplified, causing the unit to rock, slide, or even "walk." This movement stresses hoses and wiring, loosens bolts, and can ultimately lead to inefficient draining or even safety hazards.
Tools You Will Need for the Job
You do not need a professional technician’s toolkit to solve this problem, but you do need the right instruments. Relying on visual estimation alone is a common mistake that leads to frustration; the machine might look level to the eye, but it is still subtly off-kilter. To ensure accuracy, gather a bubble level—a standard 6-inch torpedo level is ideal—and a set of thin wooden shims or plastic leveling pads. You will also likely need a medium-duty wrench set to adjust the adjustable feet on the base of the pedestal. While a work light is optional, having one will illuminate the underside of the machine so you can observe the level’s placement clearly.

Step-by-Step Guide to Leveling Your Pedestal
The process begins with preparation rather than manipulation. Start by moving the washing machine so you can access the pedestal base fully. Locate the four adjustable feet, usually positioned at the corners of the pedestal’s top surface. Before making any adjustments, ensure the machine is empty and the door is open for stability. Place the bubble level on the very top surface of the pedestal, ideally close to the back edge where the weight of the drum is concentrated. Observe the bubble; if it sits squarely between the lines, the pedestal is level. If it leans in any direction, you are ready to begin the correction.
Adjusting the Feet and Testing the Result
To correct an imbalance, focus on the two feet opposite the direction the bubble is leaning. For example, if the bubble tilts toward the front, you must lower the front feet or raise the back feet. Most adjustable feet operate by twisting the inner collar clockwise to lower and counter-clockwise to raise. Use your wrench to make small, incremental turns—quarter turns are best—and recheck the level after each adjustment. Patience is the key here; you are retrying to coax the machine into perfect balance. Once the bubble rests perfectly centered front-to-back and side-to-side, lock the retaining nut if the unit has one, to secure the setting.
Validating Levelness and Testing the Machine
With the pedestal adjusted, you might be tempted to immediately run a load, but a critical validation step comes first. Slide the washing machine back into place, ensuring the power cord and drain hose retain enough slack to move freely without tension. Now, take the level and place it horizontally across the top of the drum itself, not just the pedestal. This double-check ensures the machine body is parallel to the ground. Look for a slight tilt or a rocking motion. If the machine rocks even minimally, remove it, inspect the feet, and insert shims if necessary to bridge any gaps between the foot and the pedestal surface.

Finalizing the Setup and Avoiding Future Issues
Once the machine sits perfectly still, it is time to test the mechanics. Run a short spin cycle—ideally with a mixture of wet towels or jeans to simulate a heavy load—while stepping back to observe. The unit should hum to life, then settle into a quiet, steady vibration. There should be no loud banging, no shifting sounds, and no noticeable movement of the unit’s position. If the noise is smooth, you have successfully mastered the installation. To maintain this balance, periodically check the feet if you move the machine, and ensure the pedestal’s rubber feet remain clean and intact to prevent slipping over time.























