Installing a penny round backsplash is one of the most impactful updates you can make in a kitchen or bathroom, offering a classic, timeless aesthetic that hides grime and complements both modern and vintage design schemes. These small, 1-inch tiles create a striking visual texture that is both easy to clean and remarkably durable, making them a favorite for high-use areas.
The primary challenge homeowners face with this project lies in the meticulous nature of the layout. Because each individual piece is small, the margin for error in spacing and leveling is slim, demanding patience and a methodical approach. Success hinges on precise planning and the right preparatory steps to ensure a flawless finish that lasts for years.
Preparation and Planning
Before applying a single tile, it is essential to prepare the surface with the same rigor as a major renovation. The substrate must be clean, dry, flat, and structurally sound to prevent future cracking or tile detachment. Any existing old adhesive or debris must be thoroughly removed to create a perfect bonding surface.

- Turn off the water and electricity to the area if working behind a sink or outlet.
- Remove old backsplash materials, ensuring the wall is smooth and free of grease.
- Check for and repair any cracks or holes in the drywall or cement board.
- Mark a vertical level line on the wall to serve as your straightness guide.
Gathering Your Materials and Tools
Selecting the correct adhesive and spacers is arguably more important than the tiles themselves for achieving a professional result. You will need a polymer-modified thin-set mortar specifically rated for backsplash tile, along with the appropriate notched trowel for your substrate.
| Tool | Purpose |
|---|---|
| Notched Trowel | Applies adhesive evenly for a strong bond. |
| Tile Spacers | Maintains consistent grout lines between penny rounds. |
| Tile Cutter | Crushes or scores tiles for precise cuts around edges. |
| Rubber Mallet | Gently taps tiles into perfect alignment without damage. |
The Layout Process
Layout is the make-or-break phase of installing penny round backsplash tiles. Because these tiles are small, a misalignment of just a fraction of an inch at the start of the row will magnify into a significant gap or a crooked finish by the end of the wall. Finding the center is the golden rule of installation.
Measure the width of the area and mark the exact center point. Dry fit the tiles along the floor or a flat surface first, arranging them in a pattern that pleases your eye, such as a brick bond or a simple staggered layout. This dry run allows you to determine the final grout line width and adjust the starting point so that you do not end up with a sliver of tile at the edge of the wall.

Mixing and Applying Adhesive
Once the layout is confirmed, you can mix the thin-set mortar. Mix only as much adhesive as you can spread within the open time suggested by the manufacturer, usually about 10 to 15 minutes. The consistency should resemble smooth peanut butter; if it is too runny, it will slump, and if it is too dry, it will not bond properly.
Using the notched trowel, spread a generous layer of adhesive on a small section of the wall. Comb the trowel at a consistent angle to create uniform ridges, which ensure a consistent bond height. Work in small sections to prevent the adhesive from drying out before the tiles are set.
Setting the Tiles
Begin setting the tiles at the center mark, pressing the first piece firmly into the adhesive. The key to a flat, professional-looking surface is to press the tiles straight down into the bed of mortar rather than sliding them sideways, which can cause the adhesive to streak and lose its grip.

Place tile spacers between each penny round immediately after setting them to lock in the grout line. Maintain consistent pressure and use a level frequently; it is much easier to adjust a tile when the mortar is still wet than to grind it down later. If a tile shifts, do not try to "wiggle" it into place—lift it cleanly and reapply new adhesive to avoid creating air pockets.
Cutting and Finishing
Eventually, you will reach the edges where a full tile no longer fits. This requires careful measuring and cutting. To cut a penny round, mark the tile with a pencil and use a manual tile cutter to score the surface. A common and effective technique is to cut most of the way through and then use a pair of tile nippers to gently snap the excess away along the score line.
Once all tiles are set and the adhesive has cured for the recommended 24 hours, you can begin grouting. Choose a sanded grout if your joints are 1/8 inch or wider to prevent shrinkage, or a non-sanded grout for smaller gaps. Apply the grout with a rubber float, pressing it diagonally across the tiles to fill every void, then wipe away the excess with a damp sponge before it hardens.






















