Randy Ideas

Step-by-Step: Replace Rocker Panels on a Chevy Truck

Is your Chevy truck showing its age with rusty, dented rocker panels? Don't let this eyesore and potential safety hazard go unaddressed. Replacing rocker panels on a Chevy truck might seem like an intimidating task, but with the right guidance, anyone can tackle this project. Let's dive into a step-by-step guide on how to replace rocker panels on a Chevy truck.

How To Replace Inner & Outer Rocker Panels on C10 Truck Part 3 - Rust Repair with Eastwood
How To Replace Inner & Outer Rocker Panels on C10 Truck Part 3 - Rust Repair with Eastwood

Before starting, gather all the necessary tools and materials. You'll need a welding torch, cutting torch, angle grinder, drill, wrench set, tow straps, pry bars, and new rocker panels. If your truck has a bed liner, you might also need a bedliner grinder or spot-weld cutter.

Rusted Silverado Rocker Panel Replace and Repair - Extreme DIY
Rusted Silverado Rocker Panel Replace and Repair - Extreme DIY

Preparing Your Chevy Truck for Rocker Panel Replacement

Before diving into the replacement process, ensure your Chevy truck is safe and stable. If your truck is on the ground, use jack stands to safely lift it off the ground. Remove any wheels and tires that are in the way, and block the truck securely to prevent it from rolling.

Getting Rid of Rot: Chevy C10 Floor and Rocker Panel Replacement
Getting Rid of Rot: Chevy C10 Floor and Rocker Panel Replacement

Next, remove the old rocker panels. Start by disconnected any wiring harnesses or electrical connections that are attached to the rocker panels. Use a cutting torch or angle grinder to carefully cut through the spot welds that hold the rocker panels in place. Once you've cut through all the welds, use pry bars to carefully pry the old rocker panels off. Be gentle to avoid damaging the vehicle's body.

Preparing the New Rocker Panels

How to Install Rocker Panels and Rust Removal on 1967-1972 Chevy / GMC Pickup Truck Part 1
How to Install Rocker Panels and Rust Removal on 1967-1972 Chevy / GMC Pickup Truck Part 1

Before installing the new rocker panels, ensure they're the correct fit and shape. If necessary, use an angle grinder to trim the new panels to match the shape of your truck's body. Keep in mind that most replacement rocker panels are sold as a pair, so one side should match the other.

Once you've assured the new panels fit correctly, use a welding torch to clean the truck's body where the new rocker panels will be installed. Remove any remaining rust, paint, or debris to ensure a strong weld.

Installing the New Rocker Panels

How to Replace the Rocker Panel on a 67-72 Chevy Truck - Chevy DIY
How to Replace the Rocker Panel on a 67-72 Chevy Truck - Chevy DIY

Position the new rocker panels in place, ensuring they're centered and aligned properly. Use tow straps to hold the new panels in position while you weld. Start welding from the middle of the panel and work your way outwards to prevent warping. Use medium to long welds to ensure a strong bond.

After welding, use a drill to create holes for rivet nuts, which will help secure the new panels. Use a rivet nut setter tool to install the rivet nuts. Once installed, use a wrench to tighten the nuts, securing the new rocker panels in place.

Finishing Touches

With the rocker panels installed, inspect your work for any missed spots or rough edges. Use a grinding wheel to smooth out any rough welds or sharp edges. If your truck has a bedliner, use a bedliner grinder or spot-weld cutter to restore the bedliner to its original shape.

Once you're satisfied with the appearance of the new rocker panels, give your Chevy truck a good cleaning. Wipe down the new panels and the surrounding body to remove any dirt or debris. Now that you've successfully replaced the rocker panels on your Chevy truck, enjoy the improved appearance and peace of mind that comes with a well-maintained vehicle.

Read Next