Schluter Shower Pan Kit: Step-by-Step Installation Guide

Betty Jul 24, 2026

Installing a Schluter shower pan kit isn't as daunting as it sounds. With the right tools, materials, and knowledge, you can transform your shower into a watertight, modern sanctuary in just a few hours. Here's a step-by-step guide to help you get started.

How to prep a shower for tile with Schluter Kerdi
How to prep a shower for tile with Schluter Kerdi

Before you begin, ensure you have the necessary tools and materials. You'll need a Schluter shower pan kit, thinset mortar, a notched trowel, a level, a rubber mallet, a utility knife, sealant, and safety gear including gloves and safety glasses.

Schluter Shower Kit Installation: DIY Tips
Schluter Shower Kit Installation: DIY Tips

Preparation and Installation of the Shower Pan

The first step involves preparing the shower area and installing the shower pan.

Schluter Shower Tray Extension Tips
Schluter Shower Tray Extension Tips

Start by clearing the area and ensuring it's clean and dry. Next, establish the slope for the shower pan. Use a level to ensure the high end of the pan sits about 1/4 inch lower than the low end to facilitate water drainage.

Installing the Sholder Pan

a man is measuring the width of a shower pan
a man is measuring the width of a shower pan

Begin by laying the shower pan in the shower area. Ensure the panels fit flush against each other, with the lowest point of the pan facing the shower drain.

Once the pan is in place, secure it with construction adhesive around the edges. Then, using thinset mortar, apply a 1/4-inch bed mixture beneath the pan. Allow this to dry for at least 24 hours before proceeding.

Installing the Shower Wall Kits

Showers | Schluter
Showers | Schluter

After the shower pan is secure, it's time to install the shower wall kits. Start by chamfering the bottom corners of the wall kits to ensure they fit smoothly over the angled corners of the pan.

Apply a thin layer of construction adhesive along the bottom edges of the wall kits. Press them firmly into place against the shower pan, ensuring they're level and plumb. Secure them with screws, following the manufacturer's guidelines.

Waterproofing and Sealing the Shower

The Easier Way to Build a DIY Walk in Shower
The Easier Way to Build a DIY Walk in Shower

With the shower pan and wall kits in place, the next step is to waterproof and seal the shower.

Use Schluter's KERDI-BOARD or a similar waterproofing membrane to cover the shower walls and floor. Ensure the membrane extends at least 6 inches up the shower walls and continues under the shower curb.

SCHLUTER SHOWER BASE INSTALL #shorts #schlutersystems #shower #tile #waterproofing
SCHLUTER SHOWER BASE INSTALL #shorts #schlutersystems #shower #tile #waterproofing
the shower system animation shows how to use it in an area that is not very clean
the shower system animation shows how to use it in an area that is not very clean
Schluter®-DITRA Connection to Shower Bases
Schluter®-DITRA Connection to Shower Bases
Schluter systems bathroom start to finish, Part 3 installing shower kerdi  drain, mud and membrane
Schluter systems bathroom start to finish, Part 3 installing shower kerdi drain, mud and membrane
Schluter®-KERDI-SHOWER-KIT | Shower & Tub Kits | Schluter
Schluter®-KERDI-SHOWER-KIT | Shower & Tub Kits | Schluter
a man in an orange shirt is working on a shower with the words schluter kerdi - shower kit
a man in an orange shirt is working on a shower with the words schluter kerdi - shower kit
How To Install a Shower Pan
How To Install a Shower Pan
How to Install Schluter Metal Profile - #shorts
How to Install Schluter Metal Profile - #shorts
How to install a shower bench: Schluter®-KERDI-BOARD-SB
How to install a shower bench: Schluter®-KERDI-BOARD-SB

Applying the Waterproofing Membrane

Begin by "U-notching" the membrane to fit around any obstructions like pipes or valves. Then, apply Schluter's KERDI-COLD adhesive to the back of the membrane and press it firmly into place.

Once the membrane is installed, apply Schluter's KERDI-SEAL to all seams, intersections, and edges. Allow this to dry for at least 24 hours before continuing.

Installing the Shower Curb

Next, install the shower curb. This step doesn't require any special tools or techniques - simply follow the manufacturer's instructions for a seamless fit.

Ensure the curb is level and properly sealed. Don't forget to apply Schluter's KERDI-FLEX to any gaps or voids to prevent water leakage.

Congratulations! You've just installed a Schluter shower pan kit. As a final tip, always double-check your work and ensure everything is watertight before using your new shower. Regular maintenance will keep your shower looking and functioning like new for years to come.