How to Change a Washer on a Kitchen Tap: Step-by-Step Guide

A dripping or wobbly kitchen tap is often more than a minor inconvenience; it can lead to wasted water, higher utility bills, and even water damage beneath the sink. The most common culprit behind this annoyance is a worn-out washer, a small rubber component that creates a watertight seal within the tap's valve. Fortunately, changing this part is a straightforward repair that requires minimal tools and mechanical skill. With a bit of patience and the right guidance, you can restore your tap to its original, leak-free function without the need for a professional plumber.

Preparing for the Repair

The success of this task hinges entirely on preparation. Before you touch a wrench, you must eliminate the risk of water spraying into your cabinet or onto your floor. Locate the isolation valves, usually found under the sink or behind the tap body, and turn them clockwise to shut off the hot and cold water supplies. If your valves are stuck or absent, you will need to turn off the main water meter for your home. Once the water is off, open the tap briefly to drain the remaining water from the pipes and relieve any pressure left in the system.

Gathering Tools and Supplies

Having the right tools on hand streamlines the process and prevents frustrating interruptions. You will not need a full mechanic’s toolkit, but specificity is key. Avoid generic adjustable wrenches if possible, as they can round off the nuts that hold your tap in place. Instead, gather an adjustable spanner or a set of basin wrenches designed for tight spaces. You will also need a flat-head screwdriver, a cloth to protect surfaces, and, of course, a replacement washer. It is critical to match the new washer exactly to the old one, as sizes vary significantly between tap models.

a faucet that is leaking water with the words how to change a tap washer
a faucet that is leaking water with the words how to change a tap washer

Tap TypeTypical Washer SizeCommon Cause of Failure
Compression Tap15mm or 3/4 inchConstant pressure causing rubber to harden
Ceramic Disc TapVaries (often custom)Sediment buildup scratching discs
Ball TapSmall rubber sealsWorn seals in the cartridge

Disassembling the Tap Mechanism

With the water off and the area prepared, you can begin dismantling the tap handle. Most kitchen taps feature a decorative cap on the top of the handle; pry this off gently with a flat-head screwdriver to reveal the securing screw. Once the screw is removed, you can lift the handle off the stem. You will likely encounter a retaining nut or collar below the handle; use your adjustable spanner to loosen this counter-clockwise. Support the tap shaft with one hand while you turn the nut to prevent the entire mechanism from spinning and potentially damaging the sink.

Identifying the Washer

After removing the retaining nut, you will be able to pull out the tap stem, exposing the washer. This component is usually a small, circular piece of rubber seated at the bottom of the stem or inside the valve body. Inspect it closely; you are looking for cracks, flattening, or areas where the rubber has hardened. Take a moment to note how the old washer is oriented and seated. Even though wasers are generally universal in function, improper seating is a common reason for a leak to persist after reassembly.

Installing the New Washer

Before placing the new washer, clean the valve seat where the old washer sat. Debris or mineral buildup on this surface will prevent a proper seal, leading to continued drips. Use a clean rag or an old toothbrush to wipe the area thoroughly. Take your new washer and slip it onto the stem, ensuring it sits securely in its designated groove. If your tap uses a cylindrical brass valve, the washer will typically be held in place by a small brass screw; ensure this screw is tightened snugly but do not overtighten, as brass strips easily.

How to change a tap easily and give your sink a fresh new look
How to change a tap easily and give your sink a fresh new look

Reassembly and Testing

Reversing the disassembly process is usually simple, but it is vital to do so methodically. Reinsert the stem into the valve body, replace the retaining nut, and tighten it firmly with your wrench. Avoid the temptation to crank it down with excessive force, as this can crack the ceramic components or the tap body. Replace the handle, tighten the screw, and snap the decorative cap back into place. Slowly turn the isolation valves back on, allowing the water to flow. Initially, turn them just enough for a trickle to prevent a sudden burst of pressure. Once the water flows steadily without leaks, run the tap through its full range of motion to ensure smooth operation and confirm the drip is gone.

How to Change a Tap Washer | Mitre 10 Easy As DIY
How to Change a Tap Washer | Mitre 10 Easy As DIY
Changing a Tap Washer
Changing a Tap Washer
How To Change A Tap Washer (Step By Step Guide)
How To Change A Tap Washer (Step By Step Guide)
How to replace the washers in your taps
How to replace the washers in your taps
How to Change a Tap Washer
How to Change a Tap Washer
How To Replace A Tap Washer
How To Replace A Tap Washer
How to Change a Tap Washer
How to Change a Tap Washer
How to Change a Tap Washer | Stay at Home Mum
How to Change a Tap Washer | Stay at Home Mum
How To Change A Tap Washer
How To Change A Tap Washer
Change a tap washer
Change a tap washer
How to change or a tap washer to stop dripping tap or replace the type of washer
How to change or a tap washer to stop dripping tap or replace the type of washer
Fix a Dripping Tap / Replace a Tap Washer (real example!)
Fix a Dripping Tap / Replace a Tap Washer (real example!)
How to Change a Kitchen Tap
How to Change a Kitchen Tap
Changing a Kitchen Tap
Changing a Kitchen Tap
How to replace a kitchen faucet fast? DIY change your tap with me
How to replace a kitchen faucet fast? DIY change your tap with me
Repairing a dripping tap by washer replacement and regrinding seat
Repairing a dripping tap by washer replacement and regrinding seat
How to fix a dripping washing machine tap - Washer replacement
How to fix a dripping washing machine tap - Washer replacement
How To Change a Kitchen Tap - Plumbing Tips
How To Change a Kitchen Tap - Plumbing Tips
EasyTapsplitter changes Tap washers risk free  ABDTools.
EasyTapsplitter changes Tap washers risk free ABDTools.
How To Change a Kitchen Tap - Plumbing Tips
How To Change a Kitchen Tap - Plumbing Tips
How to change a tap washer to stop dripping in minutes
How to change a tap washer to stop dripping in minutes
Kitchen mixer tap repair
Kitchen mixer tap repair
169K views · 2.7K reactions | How To Change Kitchen Taps Like A Pro #homeimprovements #How #howto #diy #doityourself #Plumbing #kitchen #reelsHeatandplumb.com | The Home Improvements Channel Uk | Facebook
169K views · 2.7K reactions | How To Change Kitchen Taps Like A Pro #homeimprovements #How #howto #diy #doityourself #Plumbing #kitchen #reelsHeatandplumb.com | The Home Improvements Channel Uk | Facebook
Replacing tap washers and O rings
Replacing tap washers and O rings