Cutting pegboard with a jigsaw is a straightforward task when you understand the material you are working with and use the right technique. Standard pegboard is made from thin plastic or resin-coated paper, laminated onto a fiberboard or MDF core, which requires a specific approach to avoid chipping the surface or tearing the fibers. With the correct blade, a few preparation steps, and a steady hand, you can achieve clean, precise cuts for any project.
Choosing the Right Blade
The most critical factor in achieving a clean cut is selecting the appropriate jigsaw blade. You want a tool that will slice through the material rather than tearing it apart. A high-quality fine-toothed blade is essential for this job.
- Tooth Configuration: Opt for a blade with 10 to 12 teeth per inch (TPI). A higher TPI results in a smoother cut because the teeth remove less material at once, reducing the risk of chipping the plastic coating.
- Blade Type: Use a standard wood-cutting blade with small teeth. If your pegboard has a thick plastic veneer, a slightly sharper blade can help prevent the plastic from melting back together.
Preparation and Securing
Before the saw meets the board, preparation is key to success. A stable workpiece ensures safety and accuracy, preventing the board from shifting mid-cut.

- Lay the pegboard on a stable, flat surface.
- Use clamps to secure the board firmly to your workbench. Ensure the cutting line is positioned just over the edge of the bench so the saw base can sit flat without interference.
- Apply masking tape along the intended cut line. This simple step helps minimize edge fraying and protects the plastic finish from scrape marks.
Marking the Cut Line
Accuracy starts with the mark. Use a pencil or a marker to draw your pattern directly onto the tape. If you are cutting out a specific shape, you can create a template from cardboard to trace around. The key is to provide a clear, visible guide that accounts for the width of the saw blade, or "kerf," so you know exactly where the blade will travel.
Setting Up the Jigsaw
Adjusting the tool correctly ensures the motor does the work and your hands stay safe. Proper setup reduces vibration and allows the blade to cut efficiently.
- Shoe Position: Ensure the footplate (shoe) of the jigsaw is flat against the board to maintain control.
- Speed Setting: Most modern jigsaws feature a trigger or dial to control speed. For pegboard, set the tool to a moderate to high speed. A faster blade helps the saw melt through the plastic cleanly rather than dragging and cracking it.
- Orbital Action: If your jigsaw has an orbital setting, engage a moderate setting. This action helps the blade move forward aggressively, which is beneficial for cutting through multiple layers or dense plastic without binding.
The Cutting Technique
With the board secured and the tool ready, it is time to make the cut. The goal is to guide the saw smoothly without forcing it.

- Position the blade just back from the marked line, aligning it with the edge of the tape.
- Start the saw outside the cutting area and let it reach full speed before lowering it into the wood.
- Gently tilt the saw forward so only the front teeth touch the material to start the cut.
- Once engaged, carefully guide the saw along the line using a steady, slow pace. Let the blade do the work—do not force it through the material.
- Keep the saw vertical and maintain a consistent pace around tight corners to prevent the blade from snapping.
Navigating Corners and Holes
Pegboard projects often require internal cutouts or intricate corners. Stopping and turning the blade mid-cut is necessary, but the method matters. When you reach the spot where you need to turn, stop the saw completely, let the blade come to a full stop, lift it out of the cut, and then re-enter the wood at the new angle. This prevents the fragile edge from tearing.
Finishing the Edge
Even with the best technique, the cut edge of pegboard can look slightly ragged. Fortunately, finishing touches are quick and easy.
- Remove the tape: Peel off the masking tape to reveal the clean edge.
- Deburr: If there are any small plastic burrs or rough spots, smooth them out gently with fine-grit sandpaper or a utility knife.
- Seal if necessary: If the cut edge exposes the raw fiberboard core, you may want to apply a edge sealant or a coat of paint to protect it from moisture.























