Finishing a drywall installation is not just about screwing sheets to the frame; it is the meticulous craft of hiding the seams and fasteners to create a flawless, continuous surface ready for paint or tile. Whether you are a seasoned contractor or a determined DIYer, understanding how to cover up drywall properly is the difference between a visible, unprofessional mess and a high-end, polished finish. This guide breaks down the process into actionable steps, from selecting the right materials to applying the final coat of paint.

Tools and Materials You Cannot Skip

Before you make a single cut, you need the right arsenal. Skimping on tools will guarantee frustration and visible imperfections. To cover up drywall efficiently, you will need a tape knife (or mud pan), a 6-inch taping knife for corners, a 10- or 12-inch knife for flat seams, a hawk (a small board to hold mud), a drywall saw, a utility knife, and a sanding block with medium grit paper. Additionally, you will need pre-mixed joint compound (mud), all-purpose drywall tape, and corner bead for inside and outside corners.
The Three-Layer Taping System

Professional finishes are built layer by layer. Do not try to achieve perfection in a single application; instead, embrace the three-layer system: the scratch coat, the second coat, and the finish coat. Each layer has a specific purpose, and drying time between coats is non-negotiable. Rushing this process is the primary reason for cracking and tape popping later on.
Layer 1: Embedding the Tape

The first coat is about adhesion. You spread a base layer of mud over the seam, press the drywall tape into the wet compound to eliminate air pockets, and then immediately apply a second layer of mud over the tape. The goal here is to embed the tape completely so that it is flush with the surface. Use the 6-inch knife to smooth the mud, removing as much excess as possible. This creates a strong "net" that prevents the seam from shifting.
Layer 2: Building the Radius
Once the first coat is completely dry, you apply the second coat. This layer is where you begin to create a radius—a taper that spreads the edge of the mud smoothly into the surrounding paper. Using the 10- or 12-inch knife, you apply a wider band of compound, feathering the edges outward. This step hides the thickness of the tape and ensures that the seam is strong enough to handle sanding without gouging the surface.

Layer 3: The Invisible Finish
The final coat is all about finesse. After the second coat dries, you lightly sand any ridges or high spots, then apply a thin, flawless finish coat. The goal is to apply mud so thin and even that it becomes nearly invisible. At this stage, the seam should be strong and smooth, requiring minimal sanding. This is the layer that determines how obvious the tape line will be under paint.
Conquering Corners and Joints

While flat seams require tape, corners demand a different solution. Inside corners are notoriously difficult, but using a flexible metal corner bead streamlines the process. You screw or nail the bead into place, then apply mud to one side at a time, letting it dry before moving to the other. This prevents the soft mud from bending the bead. For outside corners, you use outside corner bead, which provides a sharp, durable edge that resists chipping during the sanding phase.
Sanding: The Bridge to Painting




















Sanding is the bridge between a taped wall and a painted wall. However, sanding drywall dust is messy and hazardous, so wear a mask and goggles. Start with a medium-grit sandpaper to knock down high spots, uneven mud, and the edges of the tape that may be sticking up. Progress to a finer grit to polish the surface. The objective is to touch the wall with your hand and feel no ridges. If your hand slides smoothly, the wall is ready for primer and paint.
Priming and Painting the Repaired Surface
Once the dust has settled and the wall is smooth, do not go straight to paint. Apply a coat of stain-blocking primer specifically designed for repairs. This seals the joint compound, prevents the old stain or shadow lines from bleeding through, and ensures an even sheen. When you finally paint, use a high-quality roller to blend the repaired section with the existing wall. Lightly sand the dried paint with ultra-fine grit paper if you need the flattest finish possible, and you will successfully cover up the evidence of the repair entirely.