Atlas Ice & Water Shield Installation Guide

Anna Aug 02, 2026

Installing an Atlas Ice and Water Shield is a critical step in protecting your roof from the harsh effects of ice dams and water. This comprehensive guide will walk you through the process, ensuring you understand each step for a successful installation.

Ice & Water Shield Calculator
Ice & Water Shield Calculator

Before you begin, gather your materials: Atlas Ice and Water Shield rolls, a sharp utility knife, and roofing nails. Ensure your roof is clean and dry, and you're working on a calm, cool day for safety.

Drip Edge Installation | Drip Edge | Roofing How To
Drip Edge Installation | Drip Edge | Roofing How To

Preparing Your Roof and materials

Begin by measuring and cutting your Atlas Ice and Water Shield rolls to the desired length. The shield should overlap the flashing at the peak of your roof by at least 24 inches.

BS4D: Ice Dam’s, Icicles & Attic Condensation, Oh My…
BS4D: Ice Dam’s, Icicles & Attic Condensation, Oh My…

Next, ensure your roof sheathing is clean and dry. Remove any old roofing material, nails, or debris that could interfere with the shield's adhesion.

Installing the First Row

Why Every Roof Needs Ice And Water Shield | Peel and Stick Underlayment
Why Every Roof Needs Ice And Water Shield | Peel and Stick Underlayment

Starting at the eave (the lower edge of your roof), apply a continuous roll of Atlas Ice and Water Shield. Ensure it spans the full width of the roof, with a 6-inch overlap on the adjacent sheathing.

Secure the shield with roofing nails, spacing them no more than 6 inches apart. Nail it into the sheathing, perpendicular to the roof's rafters for maximum strength. Do not penetrate the shield's waterproofing membrane.

Installing Subsequent Rows

an external wall diagram with instructions for different types of insulations and materials to be used
an external wall diagram with instructions for different types of insulations and materials to be used

Continue installing the shield in an upward direction, ensuring each new row overlaps the previous one by at least 8 inches. This overlap is crucial for maintaining a waterproof barrier.

Use the self-adhesive backing on the shield for easy application. Gently press each row onto the overlapping section of the previous row, starting from the bottom and working your way up. Use nails to secure each row, ensuring they do not penetrate the waterproofing membrane.

Special Considerations and Flashing

Tech Today by Mark S. Graham 2014-11-01
Tech Today by Mark S. Graham 2014-11-01

When approaching rakes (the edges of your roof), cut the shield to fit, leaving a minimum 6-inch overhang beyond the rake edge. Secure it with nails, as before.

For hips and ridges (angular intersections of roof planes), use a Z-trim or flashing to direct water away from these vulnerable points. Install the shield on one side of the hip or ridge first, then install the flashing or Z-trim on top, and finally install the shield on the other side, ensuring it overlaps the flashing.

two diagrams showing different types of insulation
two diagrams showing different types of insulation
How to Prevent Ice Dams on Roofs | Englert
How to Prevent Ice Dams on Roofs | Englert
Keep Your Cool! Design Your Own Cooler Challenge - Maker Challenge
Keep Your Cool! Design Your Own Cooler Challenge - Maker Challenge
How to Prevent Ice Dams on Your Roof
How to Prevent Ice Dams on Your Roof
an iceberg floating on top of water in the middle of the ocean with lots of ice
an iceberg floating on top of water in the middle of the ocean with lots of ice
Why Your Roof Needs Both Ice & Water Shield and Underlayment
Why Your Roof Needs Both Ice & Water Shield and Underlayment
an article about how ice works in the house
an article about how ice works in the house
Designing for Snow, Water and Ice — Part 2 - Roofing
Designing for Snow, Water and Ice — Part 2 - Roofing
The Best Roof Underlayments
The Best Roof Underlayments

Final Inspection and Maintenance

After completing the installation, inspect your work. Check for any tears, improper overlaps, or missed sections. Repair any issues promptly to maintain the integrity of the shield.

Regularly inspect your Atlas Ice and Water Shield for signs of wear or damage. Replace any sections as needed to keep your roof protected from ice dams and water intrusion.

Proper installation of your Atlas Ice and Water Shield will provide you with years of protection. Regular inspection and maintenance will ensure your roof continues to repel ice and water, keeping your home safe and dry. Don't wait until the ice dam season - install your shield today!