Whether you were taking a short vacation and turned your
furnace
off before you left and you forgot to turn it back on, or there was a power outage that turned it off, checking whether it is turned on should always be the first step. Check your furnace for a reset button and press it.
If it comes on, problem solved, if not, move on to step two.
Check the thermostat. Anytime you have furnace problems, your first step should be to check the thermostat. Ensure it is set higher than room temperature and set to “heat. ” turn the fan switch to on. If the fan doesn’t turn on, it’s possible the furnace isn’t getting power, or the motor is broken. Change your filter. A dirty filter can cause your furnace to stop working. How often you change your filter will depend on your furnace, the type of filter and your lifestyle. To change your filter, remove the old, dirty filter and replace with a new one.
Why Does the Furnace Click But Not Turn On?
If you’ve followed the steps above and your furnace still won’t turn on, the unit’s door might be the issue. Go to your furnace and try to locate the metal door of the unit itself. Pull it open and then close it again firmly until it fits snugly in place with a snap or a click. In some furnaces, this is a safety mechanism that “tells” the furnace that it’s safe to operate. While you’re there….
The pilot light or ignition sensor is usually the most common issue when your furnace will not ignite. This is typically the problem if you can hear your furnace click on but it does not fire up. A faulty or dirty ignition or sensor is a relatively easy fix, so follow these steps, and you may be able to solve the problem yourself. First, you need to turn off the gas in the furnace. Then, remove the front panel to find the ignitor or ignition sensor. This is typically located near the burners. If the sensor or ignitor is dirty, it will need to be cleaned.
We have an atwood products furnace, model 8525-iv-dclp that i am trying to repair myself, maybe someone knowledgeable about rv furnces could give me some advice. This is the problem and what i have done so far… when the problem first occurred, whenever i turned on the furnace, first the blower turned on as it always does, then after about 10 - 20 seconds i could hear it click to try to start the flame. I assume the click sound is the igniter (or i guess they call it the electrode). The problem is that after the click, the flame or heat does not start.
There’s nothing worse than waking up on a winter day to a home that feels as cold inside as the temperature outside! if this is a situation you’ve found yourself in, a furnace not working could be what’s causing your chilly mornings. While you need to call an hvac professional right away if you smell gas or hear strange noises coming from your furnace, in some cases the problem can be minor and you might be able to do some furnace troubleshooting on your own. Here’s our list of seven gas furnace troubleshooting solutions that are safe for you to try.
If the furnace troubleshooting checklist did not alleviate your issue or you ran into one of the problems below, then call your local hvac professional to get your furnace working again. Noisy furnace: if your furnace is clicking , clanging, banging, or making other noises, this could be a symptom of a serious problem. Call a professional. Gas line issue: leave a natural gas problem to the professionals since it can be dangerous. Faulty pilot light or furnace flame: if your pilot light keeps going out, contact a professional, as the ignition switch may be installed incorrectly. Improperly installed furnace: if your furnace was installed wrong, then it could be leaking gas or carbon monoxide into your home.
Is your noisy furnace making sleep difficult? do loud sounds interrupt your focus or relaxation at home? pinging, popping, and rattling noises are common due to heat expanding the duct work. Loose screws can also contribute to this annoyance. Check all of your panel covers to ensure screws are tightened. If the noises bothering you are squealing or grinding these can indicate problems with the furnace blower motor. This fix requires more expert attention – contact a technician to determine whether repairs or replacement are needed.